The hitch pin holes will not be covered by the etrailer Rubber Hitch Cover for 2" Trailer Hitches # 22282 when inserted into your hitch as it will go in 1 inch. That's true of all hitch covers though as they do not go in the hitch far enough to cover the hitch pin holes, just the face of the hitch as that is the largest overall open area of the hitch. view full answer...
The inner diameter of the crosstube on the Draw-Tite Max-Frame Trailer Hitch Receiver part # 76225 is 1-1/2". Therefore, a trailer hitch cover designed for a 2" receiver tube opening like the Rubber Hitch Cover part # 22282 will not work for this application. With that being said I am certain you could find something to work for this application with just a bit of modifications.
I have attached a sample install video for you as well. view full answer...
There are two hitch pin hole options you can use on this Denver Broncos Hitch Cover, part # FTHS020S. The first hole measures 1-5/8 inches from the base of the hitch cover, and the other hole measures 2-1/4 inch from the base of the hitch cover.
Check out the picture I attached to see these measurements. view full answer...
The pin hole dimensions for the Harley Hitch Cover part # HDHC14 are for the center of the pin hole to the back of the hitch cover. view full answer...
The hitch pin hole on the Iowa State Hitch Cover, # ISTHRC, is 5/8 inch diameter which is the standard size on 2 inch trailer hitches. I have included a link to all of the Iowa State covers for you. view full answer...
The dimensions of the base of the Demco Hijacker Autoslide 5th Wheel Trailer Hitch # DM8550034 are approximately 35 inches long x 31 inches wide. It has a height that can be set at 15-1/4 inches, 16-1/2 inches or 18 inches.
The recommended cover for the head of the Demco Hijacker Autoslide 5th Wheel Trailer Hitch # DM8550034 is the aptly named Cover for Demco Hijacker 5th Wheel Trailer Hitch # DM14844; we do not currently carry a cover that fits over the entire hitch, including the base.... view full answer...
The shank would be the piece that you insert into the hitch receiver. So for a hitch cover like the Star Wars Darth Vader Trailer Hitch Cover # PC002282R01, there are 2 different shank options you can place the Darth Vader cover piece on so it will fit whether your vehicle has a 1-1/4" or a 2" square receiver.
It looks like you were looking for a light up hitch cover so I recommend checking out the Pilot # CR-007 which is a simple square design that fits a 2" receiver and plugs into a... view full answer...
I have gathered the width for the following hitch covers for you:
US Air Force Trailer Hitch Cover # AUT-AIRF-C Width = 4"
US Air Force Wings Trailer Hitch Receiver Cover # AMG102389 Width = 5"
US Air Force Seal Trailer Hitch Receiver Cover # AMG102388 Width = 5"
The # AUT-AIRW-C I wasn't able to measure but the emblem itself is 5" wide so I know it would be too large to fit. You will definitely be able to fit the first two options at 4" wide. view full answer...
I spoke with Au-Tomotive Gold, and my contact told me that the diameter of the Au-Tomotive Gold USMC Hitch Cover # AUT2-USMC2-C is 4 inches by 4 inches. view full answer...
The New England Patriots Logo Trailer Hitch Cover, # FTHB120S, will fit the 2014 Volkswagen Tiguan if your hitch has a 2 inch receiver opening.
Unfortunately, if you have a 1-1/4 inch receiver opening, then we do not carry a Patriots cover for that size receiver hitch. view full answer...
The part you referenced, Georgia Bulldogs G Logo Trailer Hitch Receiver Cover # CTH5S, is an all-metal hitch cover that provides three hitch pin holes for mounting in a 2-inch receiver. The measurements you requested, the distances from the back surface of the oval logo portion to the centers of the three hitch pin holes, are: 1-1/4-inches, 2-inches and 2-3/4-inches. The linked photo illustrates. view full answer...
On the Chicago Blackhawks 2" Hitch Cover # OHCC003, the measurement from the center of the hitch pinhole to the end of the tubing is 1/2 an inch. From the face of the cover to the center of the hitch pinhole, that measures 3 inches. I went ahead and attached a diagram of these measurements for your convenience. view full answer...
I went out to the warehouse and pulled a Flint Hill Goods Square LED Brake Light Hitch Cover for 2" Hitches
Item # FHG72VR, to measure the wiring. From the tip of the 4-Way to the back of the cover where the wires exit the housing it is 20 inches when pulled straight.
If this cover will work for you, I also recommend the etrailer Receiver Lock, # e98880, for 2 inch hitches to secure the cover and to deter theft. view full answer...
To determine the size of your receiver, measure the inside dimension of the receiver opening. If the measurement you get is 2 inches, then the NY Giants hitch cover you mentioned, part # HHCC2003 would work fine for you.
We do not have a New York Giants Hitch cover that will fit a 1-1/4 inch hitch. If you click on the provided link, you can see our selection of hitch covers designed for 1-1/4 inch receivers.
I have also linked you to our FAQ article that shows how to determine your receiver... view full answer...
I walked out to our warehouse and pulled the Ohio State hitch cover # AMG100390, from our inventory. The Ohio State hitch includes a 3/16 inch thick foam gasket that sits behind the plate of the hitch cover to prevent rattling.
From the back edge of the plate of to the center of the hitch pin measures approximately 2-1/2 inches. From the back of the gasket to the center of the hitch pin measures 2-5/16 inches. I have attached a picture showing these measurements.
The Ohio State Cover... view full answer...
The Nebraska Huskers hitch cover, item # 03409210165, is 8 inches tall by 5-3/4 inches wide and 1 inch deep, and it weighs approximately 1 pound. view full answer...
I went out to the warehouse and pulled a Chevy Bow Tie trailer hitch cover, # PC002207. It has an overall width of 7 inches and an overall height of 2-5/8 inches. I have included a picture that shows these measurements. I have included a link to all of the Chevy hitch covers we carry. view full answer...
The B and W Companion Hitch for Ford Factory rail kits part # BWRVK3300 that you are considering has a height range of 16-3/4" - 18-3/4" so it could easily fit under a tonneau cover that measures 18-3/4 inches from the truck bed floor. view full answer...
The bottom photo that shows a rectangular hitch cover is actually a typical photo meant to just show what the back of the Siskiyou covers look like. The actual cover is an oval like in the main picture on the product page. I went out to the warehouse and pulled a Georgia Bulldogs G Logo Trailer Hitch Receiver Cover, # CTH5S, to measure. The oval is 4-11/16 inches wide and 3-1/8 inches tall. view full answer...