bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Entegra Coach


  • Do You Have to Have 4-Way to Use Kuat Piston Pro X Bike Rack
  • Good question, and it is not a necessity for your car to have a 4-way flat trailer connector in order to use the Kuat Piston Pro X bike racks. The 4-way connector that plugs in between the bike rack and the 4-way on your car (if you had one) comes separately in a parts bag, so it is not actually attached to the rack. I have added a photo for you which shows where you'd plug it in so you can see it is not connected to the rack. So you definitely do not have to use a 4-way with the rack...
    view full answer...

  • Correct Replacement Bearing for Ram Square Direct Weld 12K Jack
  • The bearing is not included with the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K part # TJD-12000-RODNUT. There is a bearing washer at the top but the bearing is sold separately as the Replacement Bearing for etrailer and Ram Square Jacks part # TJD-12000-BR. If you take a look at the attached exploded view of the jack, you'll see there is a bearing at the top above the washer but no bearing on the bottom. I have attached an install video of said parts as...
    view full answer...

  • Is Modification Required To Install The Curt C26VV On The 2024 Toyota Grand Highlander?
  • No, you will not have to cut, drill or modify the vehicle in any way when installing the Curt # C26VV on a 2024 Toyota Grand Highlander. This is actually about as easy of a hitch installation as you will see. You will just lift the hitch into place, and put two bolts on each side. The weld nuts are already present on the frame. Might take you about 10 minutes. We have not got a chance to shoot any videos yet. I have linked the manufacturer instructions below.
    view full answer...

  • Correct Voyager WiSight Camera for Installation on a 2022 Winnebago Prewired for Voyager Camera
  • We do have what you need, but since your 2022 Winnebago 2529RG is prewired for the Voyager system you will not want to use the Voyager WiSight 2.0 Wireless RV Backup Camera System w/ Night Vision # ASA57YR that you were looking at. Because you will remove the plate completely and with that system it will leave some areas exposed. Instead, you will want to use the Voyager WiSight 2.0 Wireless Backup Camera System w/ Night Vision for Prewired RV # ASA37YR. This system has a different camera...
    view full answer...

  • B&W Continuum Weight Distribution System Installation - Do Truck And Trailer Need To Be Level?
  • Good morning! To answer your first question, yes the B&W Continuum Weight Distribution System # BW28FR will work very nicely on your Grand Design 2970RL. You are well within the maximum weight parameter of 16,000 lbs, so it will work nicely to level your ride and prevent sway. To answer your second question, yes, the trailer and tow vehicle must both be on a flat level area in order to hook up. So you will not be able to hitch up with the camper in the driveway and the truck on the street,...
    view full answer...

  • What Hitch has the Easiest Installation for My 2021 Porsche Cayenne?
  • As far as the easiest hitch to install on a 2021 Porsche Cayenne, unfortunately all of our hitches require bumper removal, wheel well removal, and fascia trimming on your vehicle. However, with that being said, for less area to cut, the Draw-Tite - 2" # DT87MR (coupe model only) requires a 4 inch x 4 inch trim while the Stealth Hitches Hidden Rack Receiver - Custom Fit - 2" # SH37FR (for both SUV and couple models) requires a 3-1/2 inch wide x 12 inch long trim. If you are considering the...
    view full answer...

  • Where Do the Wires on the Universal Install Kit for Trailer Brake Controllers Get Installed?
  • If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector # ETBC7 is meant to be used on vehicle's that don't have an existing 7-way and need to add one. However if you were adding a 7-way then you'd need to route the blue wire to the output on your brake controller, and run the yellow wire to the reverse light circuit. If...
    view full answer...

  • Recommended Hitch for a 2023 Subaru Outback
  • For your 2023 Subaru Outback, I recommend the Curt Trailer Hitch item # C69VV. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver. I really like this hitch because it is an easy install and anyone with a basic set of tools and knowledge can install it in a short amount of time. I have attached a couple of pictures below along with the instructions so you can see what this hitch looks like installed and how to do it. If...
    view full answer...

  • Installation Difficulty of etrailer Trailer Hitch on 2019 Subaru Outback
  • Thanks for the nice words, and on a scale of 1-10, the installation difficulty on your 2019 Subaru Outback is rated a 10 for the etrailer Trailer Hitch Receiver # e42TR. This is somewhat subjective, of course, and we have it as a higher rating basically because you have to remove and reinstall the bumper cover and bumper beam, and any time there is a hitch where a bumper removal is required, the difficulty scale is raised. That said, there isn't anything about the install that it requires...
    view full answer...

  • Does Stealth Hitches Trailer Hitch For 2021 BMW X5 Require Bumper Trimming
  • That's a good question, and there is no type of fascia or bumper trimming needed in order to install the Stealth Hitches # SH89VR or # SH25VR on your 2021 BMW X5. The bumper and fascia remains intact, though there is a small piece under the vehicle you will need to trim. This is a rock/gravel guard that needs a portion of it trimmed, and I added a photo with an arrow pointing the section out so you can see for yourself (the yellow circles are not relevant to the trimming, it's just the...
    view full answer...

  • Can Two Jack Legs Be Added To An Existing Ground Control 4-Point System To Make It A 6-Point System?
  • This has been asked before, and what Lippert has told us is that in order to turn your 4-point system # LC358590 to a 6-point system # LC675817 you'd have to purchase the entire new 6-point system, unfortunately. The two additional jack legs can not be added to the existing 4-point system. Attached are a couple of product review videos for you to check out as well.
    view full answer...

  • Will Air Pressure Transfer Between Air Bags With Union Tee Installed
  • Installing the Union Tee # AL21838 with your # AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say potentially is because it depends on the pressure you are keeping in the air bags. If you have them both at the max 100 psi I would expect full support between the two. If you are keeping them at 95 psi there won't be much room for pressure...
    view full answer...

  • How To Wire In The LaSalle Bristol 12V RV Ceiling Fan w/ Wall Switch # 344410TSDC42BNBK
  • The four wires in the picture of the 12V RV Ceiling Fan w/ Wall Switch # 344410TSDC42BNBK you referenced are coming from the wall remote # 344410TSSW12V. You'll wire the wall remote in the following manner: White: Fan Motor + Blue: Fan Motor - Black: Trailer Battery - Red: Trailer Battery +
    view full answer...

  • Does Etrailer Trailer Hitch Receiver e95ZR For 2022 Hyundai Palisade Require Bumper Modification?
  • The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" # e95ZR does not require any trimming or modification to your bumper molding or fascia. You will, however, need to remove the passenger side plastic molding temporarily but it can be re-installed right after the receiver is installed. Nothing will look out of the ordinary as you can see in the attached photos. We do not have an installation video for this exact receiver, but I did attach an installation...
    view full answer...

  • Base Plate Installation Instructions For A 2023 GMC Canyon AT4
  • I am sorry but we do not have any alternate instructions for the 2023 GMC Canyon AT4. This Demco base Plate # DM27YV (9519361) is fairly new and we have not had the chance to install one here at our shop yet. If it helps, I was able to track down instructions for the Roadmaster base plate # RM98GR which is also for the 2023 GMC Canyon AT4. The design of the base plate is different from the Demco, but their instructions do show a GMC Canyon. They have some good pictures in there which...
    view full answer...

  • Are Safety Chains Required When Using Curt CrossWing Gooseneck-to-5th-Wheel Trailer Hitch Adapter
  • Safety chains like the Curt # C95NR aren't required when using the Curt CrossWing Lightweight Gooseneck-to-5th-Wheel Trailer Hitch Adapter # C32DR but if you want to attach safety chains there isn't any harm in that either.
    view full answer...

  • How To Fill Dexter EZ-Lube Spindle/Hubs With Grease And How Often Should They Be Filled?
  • The spindle on your Dexter axle is going to be similar to the #84 E-Z Lube Spindle # TRU74FR in the image below. You can see there is a hole in the spindle where the grease will push through into your inner bearing. From there it will move along the spindle to the outer bearing where you will see the grease begin to push out the bearing and fill the grease cap. When filling you will want to turn the hub to ensure grease gets pushed through the entire inner bearing. This process should be...
    view full answer...

  • Can etrailer Horizontal E-Tracks e42VR Be Installed By An Amateur?
  • You can absolutely install E-Tracks like the etrailer Horizontal E-Track - Black Powder Coated Steel - 2,000 lbs - 94" Long - Qty 4 # e42VR you were looking at in your Forest River Enclosed Cargo Trailer yourself. Now there are a few things to keep in mind, as no trailer is the same. The ideal way to install E-Tracks is in a location where you can screw into the frame of the trailer and not just the wood. Using 1/4" x 1" self tapping screws will be perfect for grabbing into the frame,...
    view full answer...

  • Why Do You Need the 5th Wheel to Gooseneck Adapter W/ A MORryde Cushioned Pin Box?
  • The reason you'd need the 5th-Wheel-to-Gooseneck Coupler Adapter Mounting Plate for MORryde Pin Boxes # MR37ZR is because in order to use a 5th wheel to gooseneck adapter like the Ranch Hitch Universal 5th-Wheel-to-Gooseneck Coupler Adapter # AM3100 you'd need to drill into your pin box to attach it which you wouldn't be able to because you'd damage the cushioning and may void your warranty. This plate would take the place of your current king pin and will allow you to use a 5th wheel...
    view full answer...

  • What is the Purpose of the Trailer Valet Trailer Wheel Dolly for Tandem Axle Trailers
  • Thanks for reaching out! The purpose of the Trailer Valet Trailer Wheel Dolly for Tandem Axle Trailers # TV56FR is to give you better maneuverability with a tandem axle trailer when utilizing a trailer dolly like the Trailer Valet XL # TVXL25. The smaller wheels can swivel like what you see on an office chair or shopping cart so it keeps one sets of tires from dragging. This type of product is best used for needing to maneuver a tandem axle trailer into a space that requires tight turning...
    view full answer...