As long as your existing landing gear have their weld stops in the standard positions as shown in the linked photo (15-1/2 inside to inside and 17-1/2 outside to outside) and the outer tube length matches then the Ultra-Fab 12K dual motor landing gear set # UF17-943010 will install easily in its place in the existing hangers. But if not the Ultra-Fab includes new hangers that you can weld to your frame. This jack system's high 12K capacity and independent motor control will make leveling... view full answer...
We do have wheel bearing caps for your 2008 Dutchmen Freedom Spirit Superlite Travel Trailer. It depends on which model you have.
The Bearing Buddy Bearing Protectors - Model 2441SS - Stainless Steel (Pair) item # BB2441SS fit the FS290SL and are 2.441 Inch.
The Bearing Buddy Bearing Protectors - Model 2328SS - Stainless Steel (Pair) item # BB2328SS fit the FS310B-DSL, FS180, FS250SL, FS260B-DSL, FS260F-DSL, FS290R-DSL, and the FS270.
It depends on which model you have and how the hub... view full answer...
Yes, the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box # GY66FR is the correct weight capacity and bolt pattern for your 2021 Dutchmen Voltage 4225 5th Wheel Toy Hauler. It uses the same 1621HD bolt pattern as the Lippert Trailair Rota-Flex Pin Box # LC328329 that comes on your Voltage.
The Gen-Y is rated for a tongue weight of 3,500-5,500lbs and your dry tongue weight is 3,685lbs. The maximum trailer weight is 25,000lbs and your Voltage is rated to 20,000lbs.
You might... view full answer...
The Stromberg Carlson RV Exterior Ladder w/ Hinges # LA-401 is a universal fit so it will work great on your 2017 Coleman 250TQ Toy Hauler as it can go on the side or rear of your trailer.
This ladder measures 12" wide and is 99-1/2" tall but you can customize its height by trimming the legs with a tube cutter or hacksaw and you only need to be sure you know the locations of your Coleman's blocking or sub frame so you can properly mount it, as you can see by the cut out of the linked... view full answer...
I can tell you how to determine if the Landing Gear Set # RVLG-8000 will fit your 2007 Dutchman Colorado 5th wheel, though landing gear is a universal type of fit, and there isn't landing gear that is a specified fit.
It's pretty easy to determine though, as all you will need to do is measure the distance between the mounting brackets on your Colorado as shown in the diagram. So long as that measurement is 17-1/2 inches from the top of the upper weld stop to the bottom of lower weld stop,... view full answer...
The correct replacement for your Dometic 600315.331C RV Air Conditioner is the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners - Beige # AT3308046006. view full answer...
Yes, it would be safe to use the Patriot Hitches Adjustable Drop Hitch Receiver Adapter - 2" Hitches - 11" Rise/Drop - 7K, part # PH54FR, with the etrailer Motorcycle Carrier w/ Ramp for 2" Hitch - 76" Long - Steel - 500 lbs, part # e98873. You should not need to add an anti-rattle devices, it has a built in anti-rattle device. You also have an anti-rattle hitch bolt in your motorcycle carrier. This adapter will provide you will 11" of drop, but please keep in mind that anytime you add... view full answer...
For your 2016 Dutchmen Denali Travel Trailer I recommend using the Stromberg Carlson RV Exterior Ladder part # LA-401BA. This ladder like all of our options is universal which means it will fit a variety of different trailers. It comes in a painted black finish and has a one year warranty. The length is also customizable so you can make sure you get the perfect height. view full answer...
The Grease Seals # RG06-050 are the ones most likely to fit your 2018 Dutchmen Kodiak Travel Trailer.
You can confirm this by removing the hubs ahead of time(This is recommended so that you can inspect the bearings to see if you will require those as well). You will generally be able to find the measurement stamped into the seal. If you are unable to read the measurement you can see the article linked below on how to measure for that seal as well as the bearings and races.
When you... view full answer...
The "LCI35" indicates that your Lippert axle uses 3,500 lb bearings and seals, and the correct bearing kit is the following:
- Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles # BK2-100
Then for wet bolts you can use the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs # 126B2. view full answer...
The Lippert Components High-Speed Power Stabilizer Jack # LC369774 is designed to mount to existing holes that are spaced apart by 68-11/16 inches on center. As long as your Northshore Toy Hauler features the necessary bolt hole spacing on the frame the stabilizer jack will work perfectly to replace what used to be there.
Because Lippert products like these are often installed at the factory it's very likely that the old electric stabilizer on your toy hauler was just a previous version... view full answer...
The Alpha Systems Alphabond Repair Tape for RV Roofs # AL32KV is compatible with EPDM as well as wood, metal, fiberboard, ISO board, concrete, TPO, PVC, and mixed elastomer roofing membranes. view full answer...
I would love to help but we do not have any information on your 2005 Dutchmen Denali Fifth Wheel Trailer therefore, in order to determine compatibility of the SolidStep Manual Fold-Down Steps you will need to take two measurements. The first measurement is going to be the width of your door frame (inside to inside). The second measurement is going to be the height from the ground to the bottom of the door (top to bottom).
If the above width is between 28" - 30" and the above height is... view full answer...
The Foggati tankless water heaters are 100 percent going to be an upgrade over a standard water heater due to their efficiency, as it only uses energy when you turn on the hot water instead of a standard heater that is always using up energy to keep the water hot.
And while it is very likely to fit, we don't have any way of knowing fits of a heater in any specific trailer, so you'll just need to take some measurements for either of the Fogatti heaters, which are the following part numbers:
-... view full answer...
Your Lippert Axle uses 1/2"-20X1.99" studs that have a 0.617 knurl for seating in the hub. I can recommend you a replacement hub assembly that does have the 9/16" studs, as I cannot locate any 9/16"-18 studs that have the same knurl dimensions.
The etrailer Trailer Hub and Drum Assembly # AKHD-865-7-1-K come preloaded with the 9/16" studs, lug nuts, new races, and bearings as well as a grease seal. This will also save you the time of having to press out and in all the wheel studs on your... view full answer...
The 1/2" SAE Swivel fitting on the # 37207-31465 you were looking at would require a 1/2" SAE male fitting. SAE fittings have a straight thread and require an O-Ring for a proper seal, while NPT uses its tapered thread pitch for a seal. Using the two together can lead to leaks.
You should be able to find a 1/2" NPT female to 3/8" male flare fitting at your local hardware store and from there you could use a 3/8" swivel female flare fitting hose to whatever style fitting you need to connect... view full answer...
To determine the correct size RV storage cover for your Coleman Lantern LT Travel Trailer you'll need to measure the body length. In the attached picture below you'll see exactly how to measure. Once you have this measurement you can choose the correct length from the options below:
15' - 18' # AD37ZR
18' - 20' # AD97ZR
20' - 22' # AD47ZR
22' - 24' # AD67ZR
24' - 26' # AD77ZR view full answer...
The only way to determine the correct size entry lock for your 2011 Dutchmen Aerolite 195QB Travel Trailer would be to remove the backing plate of the existing door lock and measure the cutout hole.
For example, the Bauer Products Camper Door Lock # BA94FR you were looking at requires a cutout hole 2-3/4" wide x 3-3/4" tall. view full answer...
There are two air-ride style pin box replacements for the Lippert 1621HD pin box on your 2018 Dutchmen Voltage Epic Toy Hauler- the Trailair Air Ride # LC158778 and the 5th Airborne # RP78FR which both have a capacity of 21000-lbs.
Both of these pin boxes are designed to help create a smoother ride with less chucking and the elimination of the bouncing and jarring that comes with towing a 5th wheel. They're both extremely similar, but I prefer the Trailair # LC158778 because of the cushioning... view full answer...
The difference between a hub connection and a spigot connection is that the hub is the female end and has a lip on the inside that stops the spigot (or male) end where it needs to be. I have attached some pictures to assist.
With this knowledge it is just a matter of taking your valve off and choosing the correct replacement:
3" Hub to 3" Hub - # E40B-8
3" Hub to 3" Spigot - # E40-8
3" Spigot to 3" Spigot - # E40A-8
I would avoid going with the option that only has the 3" Diameter #... view full answer...
Go To Results