The Ultra-Fab Chock and Lock Wheel Stabilizers for Tandem-Axle Trailers # UF21-001070 is a wheel chock system that performs the function of a traditional wheel chock, except that by its design it eliminates any movement and is lockable to deter theft. view full answer...
For the Fastway ONEstep Wheel Chock # FA84-00-4000, the 16 inch to 24 inch wheel spacing is measured from end point-to-end point of the wheel chock. Since the chock is adjustable, the smallest it will measure is 16 inches, but it can be adjusted out to 24 inches.
If you need a chock with larger spacing, you can use the ONEstep XL # FA84-00-4150. This chock can be adjusted form 24 inches to 30 inches. view full answer...
Most RV wheel chocks like the part # 288-02011 are around 6 inches tall. Most of the time two chocks is ideal. Putting one behind the rearmost wheel and then in front of the forward most wheel on the same side of the trailer will prevent it from moving. view full answer...
The Stallion Wheel Chock # 288-02011 referenced in your question weighs in at just around 5 pounds.
The wheel chock is constructed of high-impact polyurethane that will hold up under tremendous weight. The material itself is the orange color you see, so you will not need to worry about any paint flaking off with use. It's possible that the color might fade a bit down the line simply due to exposure to the elements, but the distinctive orange will still hold up great.
This will come with... view full answer...
A motorcycle tire of size MT90-B16 has a width of 5-inches (up to a shade over 5-inches at most).
The motorcycle wheel chocks we offer are all shown on the linked page. These all fit a range of tire widths and diameters. The Erickson # EM07506 Removable Motorcycle Wheel Chock fits tires up to 6 inches wide and can be removed when not in use. view full answer...
The distance between the mounting holes of the Erickson wheel chock kit part # EM98CV from left to right on center are 4-1/2 inches. view full answer...
The wheel chocks in Pack'Em Wheel Tie-Down Kit # PK-WTD are 1-5/8" tall x 7" wide x 5-5/8" long. I have included a picture showing the measurements. view full answer...
The 4 carriage bolts (and related hardware) supplied with the MaxxTow Adjustable Wheel Chock (DISCONTINUED) MT70075 are intended to semi-permanently install this unit on the floor of a trailer. This wheel chock is not intended for routine removal and re-installation although it certainly could be taken off your trailer by removing the mounting hardware. The carriage bolts supplied are 3-inches long overall and include a washer, plastic spacer and nylock hex nut.
If your trailer's floor... view full answer...
The measurement you're referring to for the Erickson Removable Motorcycle Wheel Chock # EM07506 is 8". This wheel chock has overall measurements of 11-3/4" long x 8-1/4" wide x 8-1/2" tall and will fit tires up to 6" wide. view full answer...
The height of the chocks that come with the Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks # EM98CV is 2-1/8" when they are mounted. These would be a great solution for securing lawn mowers on your trailer as long as you stay within the allowed weight and tire size. The # EM98CV has a safe working load limit of 1,500 lbs and fits 10"-30" tires. view full answer...
No, they do not. The Stromberg Carlson Chock Wheel Stabilizers item # SC47MR are only available in the shiny steel finish. All of our wheel stabilizers have this finish so they are noticeable and prevent people from attempting to drive off with them still set up. view full answer...
The Buyers Products 9-1/2" Wheel Chock w/ Recessed Chain Eye - Black Rubber # 337WC6810L that you referenced is a 7 lb wheel chock that will do a great job on a boat ramp. If the ramp is really steep I would exercise caution still if the ramp is also wet at the time. view full answer...
There are 3 holes in the mounting surface of this wheel chock. One is
in the center of the strap at the front of the chock and the other two
are in the back strap. The front to back measurements are as follows,
from the center of the front mounting hole straight down to the centers
of the back 2 mounting holes is 7 inches. If you measure on the
diagonal line from the center of the front mounting hole to the back
mounting hole on both sides the measurement is 7-1/4 inches. The 2 rear... view full answer...
The # RA-17 Motorcycle Wheel Chock is designed to be used along with tie down straps to secure a motorcycle during transport. As long as the straps you're using have the proper weight rating for the 700 lb weight of your bike, the # RA-17 will be plenty sturdy. Erickson offers # EM05710 Ratcheting Motorcycle straps sold in pairs that have a 400 lb capacity per strap. Two straps would more than cover the 700 lb weight of your bike. If you click the provided links, you can see product demonstration... view full answer...
The Rack'Em Manufacturing Removable Wheel Chock # RA-17 is 8-9/16 inches tall. There are additional measurements in the attached video that may help you see how this product would work for you. view full answer...
The overall dimensions of the Rack'Em Manufacturing Removable Wheel Chock # RA-17 are 10-1/2" wide x 10-1/4" long. It measures 8-9/16" from the base to the top of the chock and fits tires up to 6-1/2" wide. view full answer...