Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 1

See what our Experts say about this Spectro Wiring

• Tapping Into Running Light Circuit for Deck Lights
  Using the running light circuit from the trailer wiring of your vehicle would work to power the running lights. You could use butt connectors # 224775 to do this. You'd have to cut the running light circuit ran to the 7-way and then use the one end of it to reconnect the circuit and then on the other end you could run the new light circuits.
  view full answer...
• What Color Butt Connector for Red Wire of Redarc Brake Controller
  Blue butt connectors are for 16-14 gauge wire so what you would need is a yellow one like the part # 224775 which is designed for 12-10 gauge.
  view full answer...
• Butt Connectors to Use with Curt Trailer Wiring Harness # C62VR
  According to Curt the recommended butt connector to use with the Curt # C62VR would be a yellow one like for 10-12 gauge wire like the part # 224775.
  view full answer...
• Do All Yellow Butt Connectors Have Built In Heat Shrink Feature?
  Most butt connectors are not designed with heat shrink built in, only specific ones like the # DW05745-5. If you have just standard butt connectors like # 224775 you'll need to pick up heat shrink # DW05449 separately. Any connectors exposed to the elements should have heat shrink protecting them.
  view full answer...
• Recommended Replacement Trailer Jack for a Northwood Arctic Fox
  The Electric Trailer Jack A-Frame part # EJ-3520-BBX for black or part # EJ-3520-WBX for white is an excellent option for a Northwood Arctic Fox. The Electric Trailer Jack A-Frame will also work just fine in cold weather as well so there should be no issues here. In regards to capacity, the Electric Trailer Jack A-Frame has a 3,500 lb rating which will exceed the Northwood Arctic Fox. The higher the weight capacity of the jack is in relation to the weight of the trailer, the longer it will...
  view full answer...
• Trailer Brake Controller Recommendation for 2008 Monaco Camelot Motorhome on Roadmaster Chassis
  We don't have a schematic for the 2008 Monaco Camelot 40 foot, so I can't tell you where that wire is connected. I recommend looking under your dash and using a circuit tester like # PTW2993 to test. You can connect a battery to the 5 o'clock pin of your 7-way and then test for that 12V on wires under your dash. Confirm the correct fit by unplugging battery connection and testing again to confirm no power on that wire. Once you have found the correct wire, you can install your Prodigy...
  view full answer...
• How To Run a 12 Volt Power Wire for the 7-Way on a 2008 Chevrolet Silverado
  The 12 volt power wire that goes from the power distribution center to your 7-way trailer connector should be a red/black wire but so long as you are splicing into the one that is ran to to the correct terminal (see photo) then color will not matter. Once you have this wire you will need to cut it in two, splice the end from the connector onto part # 10-1-1 (per foot) with part # 224775 and then run this wire up to the power distribution center stud with part # 185917 and part # DW05705-1.
  view full answer...
  
• Installing Roadmaster 12 Volt Outlet Kit to Rear Cargo Area of Subaru Outback
  The 12 Volt Outlet Kit, 20 amps # RM-9332 will work just fine with you adding a longer wire to your battery. I recommend # 12-2-1 sold by the foot along with butt connector # 224775 or heat shrink connector # DW05745-5 for a better weather seal if needed. I recommend connecting directly to the battery and not at the fuse box. You will also want to make sure you leave the fuse in a location that is accessible if you need to replace at some point. I've attached some videos and an article...
  view full answer...
• Can Maxxair Deluxe Roof Vent MA00-06200K Mount Off Center on Van Roof
  MaxxFan Deluxe 12V Roof Vent # MA00-06200K and similar RV roof vents can be installed off-center in the roof of your Transit T-150. The minor difference in depth from the roof corrugations is not an issue since you'll be using an install kit with flexible sealant like # 344270KITW. For wiring the vent to your 12V power I recommend using 10-gauge wire # 10-2-1 and butt connectors # 224775.
  view full answer...
  
• No Power to 12 Volt Circuit for Trailer Jack on a 2008 Chevy Silverado 2500HD
  The most likely cause of the 12 volt power circuit on your 7-way not being active is due to an unconnected wire on your power distribution center (PDC). This is rather common for these vehicles so that is what I would check first. If you take a look at the attached photo you will see where the wire should be located. If the wire is already connected then odds are you have a short in this wire which would mean your best option is to just run a new one with part # 10-1-1 (per foot), part...
  view full answer...
  
• 4-Pole Wiring Harness Kits for 2016 Ford Transit T250 & T150
  The Curt # C56327 is a confirmed fit on both the 2016 Ford Transit T150 and T250 if they do not have the factory trailer wiring setup. This has custom-fit connectors that plug in at your taillight wiring; it has a white ground wire that will attach to the vehicle metalwork; and it has a single power wire that you will need to run up to the engine compartment to connect to the battery + terminal using the supplied fuse holder. The power wire for either kit can be run on the outside of...
  view full answer...
• Recommended Replacement LED Trailer Tail Light Assembly for Keystone Montana Fifth Wheel
  Taillight assemblies such as the LED Trailer Tail Light - Stop, Turn, Tail - Red Lens - Passenger Side, # 328-003-81M1 do not have bulbs to replace. These are fully constructed with the Light Emitting Diode placed in the housing instead of a removable bulb design. Use # 328-003-81LM1 for the drivers side as this has the license plate bracket and the light on bottom side to illuminate the license plate. This is an 8-11/16" x 3-7/8" LED Trailer light with 22 diodes that provide stop, turn,...
  view full answer...
• How to Install the Peak Backup Camera Part # PKCOBU7 on a Horse Trailer
  The first step for installing the Peak Backup Camera Part # PKCOBU7 would be to mount the rear-view camera somewhere inside the horse trailer. You can use the Self-Tapping Fasteners for License Plates and License Plate Frames part # CR80430 to install the bracket/camera. Once the camera is in position, you will have two wires to connect. One will be red for the 12-volt power and the other will be black for the ground. Strip about 1/4" of the jacket off of each wire. Once done you will...
  view full answer...

Do you have a question about this Wiring?