To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
These custom-fit clamps and pads let you mount 4 Inno XS200, XS250, or INSU-K5 feet to your vehicle's naked roof to help create an aftermarket roof rack system. Clamps mount to feet with bolts. Kit includes 4 clamps and 4 pads.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, on our 2016 Toyota Camry, we're going to be test fitting the Inno Aero roof rack system consisting of part numbers INXB130-2, these are the Inno Aero crossbars, 51-inches long, part number INXS250, and these are the Inno through feet for the Aero crossbars, and part number INK872, and this is the custom fit kit for the Toyota Camry. The Inno Aero roof rack system is great for putting accessories up on your roof and freeing up space inside your vehicle. With removing our end cap here, you can see it has this nice rubber strap along the center here. Now, that coupled with the aerodynamic features of the bar will cut down wind noise and drag. Also, by pushing down on this, you can install T track accessories for your roof rack. Now, a lot of other roof racks will require you to remove the rubber strip and cut it to length, but this, all you have to do is push it down. Then reinstall your end cap. All of our through feet have these locking end caps here, so once you install this onto your roof, it's going to be secure to your roof.
The two bars combined have a carrying capacity of 120-pounds, although you always want to check with your vehicles manual to make sure it can withstand that weight. Now that we've gone over some of the features of the roof rack system, let's go ahead and show you how it installs. We have a rear bar partially assembled on our table here, and we'll show you how the other half goes together. Slide this out on the inside, and you'll see that on the bracket here, we have this little marking here and it's going to fit in perfectly like so. We'll slide it all the way back in, and then get ready to install our foot. Unlock the end cap here.
Then we'll line up this top piece of our foot with this empty slot here on the inner bracket that we just installed. Then line up our screw with this portion here. We'll push it into place, and then push it down the channel. Next, we'll get our measurement set between our two feet, as prescribed in the instructions. We'll slide our foot back till it's set. Once everything is set between the two, we'll completely tighten them down using our included Allen tool.
Now we can start installing our fit kit. Our fit kit will consist of two items. We're going to have the rubber pad here and our clamp. Now, the rubber pads are labeled, so make sure that the right pad goes with the right foot. Also, you'll see that it has these marks here that actually fit with these indentations on the foot.
Just line them up properly, and they just push right into place. Next, we'll install our clamp, which just you unscrew the end here, place the clamp on, and then reattach it loosely just to hold the clamp in place. Finally, we'll put our end cap into place. Now we're ready to install it on the roof of our vehicle. The measurement we're going to set here is going to be from the center of the door jamb to the center of our rear bar. We'll do this on both sides to make sure that the bars are parallel. We'll tighten up the clamps just so they're snug up against our door. We'll do this on the other side as well. The tool that we have here actually clicks once it's completely tightened down so you don't over or under tighten. Our final step is to put on our locking end caps, we'll do this on both sides as well. We'll take our hook ends here, place them on these portions, and you just push up and lock it in place. Now, there is one other thing I'd like to go over. You'll notice on the table earlier, we had this foam pad here. You would actually push this to the inside, here, and then cut it to length to take out the noise that would be created by this gap here. For demonstration purposes, we'll leave that out. Now we're ready to load up our accessories and hit the road. There you have it for the Inno Aero roof rack system on our 2016 Toyota Camry.
Average Customer Rating: 4.8 out of 5 stars (611 Customer Reviews)
These custom-fit clamps and pads let you mount 4 Inno XS200, XS250, or INSU-K5 feet to your vehicle's naked roof to help create an aftermarket roof rack system. Clamps mount to feet with bolts. Kit includes 4 clamps and 4 pads.Firstly, I need to thank Joseph (JosephI@etrailer.com) at etrailer. I needed a roofrack in a short period of time for a trip from MO to WA for summer vacation for my wife and kids to have extra storage. Joseph went out of his way to walk the warehouse to ensure the product I needed was easily accessible to get to for shipment. Joseph's customer service, knowledge of the products, and understanding of the logistics was incredible. I ordered the product on 25May and received my roof rack on 26May. My jaw dropped when it arrived so quickly. This is the customer service that makes it so if i ever need products offered by etrailer that I will order directly from your company and not browse Amazon for subpar products. Overall, I'm impressed thanks Joseph and the etrailer team!
It’s NOT good for a Toyota Camry. It put dents in the side rail (top of car) that it attaches to. The product it’s self works well and has held up outside of the foam tubing that protects your items from rubbing against the uprights.
I followed directions and the rack went on without a hitch. The measuring tape provided was a bit confusing but my tape measure did just fine. It pays to watch for any movement of the stays as you tighten them. It fit perfectly. I was impressed with the quality of the unit. The torque wrench provided was a nice bonus. I attached a boat rack for my rowing shell and I’m confident it will be safe all the way to the water.
Working as hoped. Easy on and off, protects the car well.
Amazing! Great product and great servic e!
etrailer was great to order from! Going to the website makes it easy to see what roof rack will fit your vehicle. Ordering process was a breeze and the fulfillment updates were great. Ordered on the 13th and received it on the 16th so the FREE shipping was super fast. New installs of anything can always be challenging but once I read the the instructions it all went pretty smooth. Installing this Inno Roof Rack onto our 2021 Tacoma TRD Sport was pretty simple and took less than an hours from start to finish. Now we are ready to load up out Thule cargo carrier when we hit the road.
I am writing this review in the context of an owner of an old Yakima roof rack system from many vehicles before the 2021 Hyundai Tucson on which I just mounted four INNO separate sets of components to carry two bikes on top of the Tucson. Note that you need at least three sets of components to have a "base rack" system, including the hooks, in this case the INNO INK680, the INNO INSUT Feet and the INNO INB137 set of crossbars. The feet are rubber coated metal so that they will not mar the paint where they clamp to the edge of the roof just above the doors. The rubber pads are also substantial to provide a slip-proof and paint protecting bottom for the INSUT feet. Read through all the directions for all the components before beginning installation, perhaps even "rehearsing" all the steps before actual installation with tightening everything. The instructions could be clearer, but with practice walking through all the steps they make sense. Once installed, I could grab any part of the completed system and pull upwards, sideways, forwards, and backwards without any play or slack in any of the components. In fact, it was easy to rock the whole car side to side without budging the INNO components at all. Compared to the old Yakima system, the INNO is just as sturdy and substantial if not more so. Just to replace the Yakima "feet" to use my old round Yakima crossbars would have cost more than the total of the three INNO components needed to get the base system. Even better, the INNO system came with included locks to lock the system to the vehicle. Many years ago, the Yakima four lock cylinders were $[XX] extra - probably much more now. So, I think the INNO is at least as sturdy and capable for much less money.
Feels premium and was pretty straight forward to install. I think it looks really good on the 2019 Honda Accord Sport. I plan to pair it with the Inno Wedge 660 cargo box. So far, it seems really well made and has a rubberized texture throughout. I installed it by myself in about 30 minutes without the instructions. It also shipped in only 2 days.
These Inno racks are very high quality, and the installation is straightforward. They look good, too.
I've been a happy etrailer customer for years. Sales staff helped me pick out the right roof rack setup for my new 2023 Escape that worked with my low-profile rails. 3 separate boxes of pieces but they all came together perfectly. Very happy with my purchase and etrailer customer support! Rack is solid, low wind noise and will work with the accessories I need, kayak carrier and cargo basket.
We bought this along with the INTR - Inno Feet for Square Crossbars. We used this to mount Thule crossbars and a Thule Adventurer cargo box on a 2001 Subaru Forester. Everything fit perfectly. The Inno mounts were completely compatible with the Thule crossbars. The fast and accurate shipping helped avert a crisis before a cross country trip.
THEY DID IT AGAIN! I was looking for roof racks for our 2012 Honda Crosstour. OEM was not available. I called Etrailer and spoke to Anna and she listened to make sure we got just what we needed.Today I'm going to install and hope they fit our needs. I'm really impressed with Etrailer and there customer service! They have taken care of me many times with several different vehicles! Thank you
Works great wouldnt have bought anything else and protects paint from getn scratched since i dont roof rails
My wife and I bought a 2019 Tyson with a bare roof and wanted a rack system that would be safe affordable and easy to install and not having to Buy and installed side rails. The Inno system was perfect. . It is solid material with a solid build. The directions were a bit confusing but after some time and with the etrailer how to videos it really made the difference. Ordering was simple and fast. Madison was great to work with she was knowledgeable and helpful. The delivery was fast and exactly on time. I was going to go with another company and another rack system…. I’m glad I didn’t. I saved money and got a great product from a great company. Thanks etrailer, Inno and thanks Madison! And mostly for making my wife happy bc know we can get to kayaking!!!
etrailer gave me fast shipping and a great price. Inno quality is great. I’ve had this on for several months and use it to transport bikes. I use the cheap bike racks on [online] but they work.
I purchased the Inno Rack system and Rhino Rack 581 saddles for my 2007 Mercury Montego. The instructions were easy to follow, and the rack is rock solid. It makes loading and unloading my kayak a breeze. I previously used roof pads and that was ridiculous compared to what this rack does for me now. I am amazed with how quiet with and without the kayak attached is - I don’t hear anything except the very slightest amount of wind with the windows open on the highway. I always have put a one turn twist in the bow and stern straps, but for the rest they’re all straight. I added an extra strap on the rear crossbar that goes behind the rear combing of my cockpit for extra security- but that’s just me. I’ve included a photo to show my setup. Thank you so much Mark S, Becky B, Carol C, and George J. etrailer rocks.
I have a 2022 Lexus GX460 Premium. Fairly simple installation and a almost seem less transition from the fit kit to the cross bar system. Can be done by one person, but I would suggest a two-person system to expedite the process.
Everything is good so far...the Inno rack system appears to made of good quality, fit and finish...it took about 2-hrs to get everything built, lined up, adjusted, tightened, loosened, repositioned, then retightened down...but I’m a bit of a perfectionist with things like this...plus I was checking my Saris cargo bin and various attachments, make sure that they’d all, which they do! And very well I might add...I just need to buy some new square carriage bolts for the channel now, along with new knobs...hoping that etrailer will get back to me with info soon...I will likely get a new wind deflector too...yesterday I did a test drive, was very pleased with the minimal whistling that occurred, and that was primarily between 30-40 mph and it was much quieter than my old Saris Roof Rack....after 40 mph the whistling got much quieter, very faint high highway speeds
Great system. Got it installed the night before a road trip, and once you get the hang of if, assembly is easy and intuitive. This system is rock solid and well done.
Things I wish I knew that would have helped in my decision:
1) After you install the footbeds, the rails and tower easily remove as one unit in the future, and they include little covers to put over the feet. No more long debates about wind noise. If you find them modify or don’t like the look, take it off in five minutes. Even the Allen wrench is stored neatly in the rack.
2) I had been a long time Yakima user, so that’s where I started with my GX rack. Having searched far and wide for landing pads, I was all set. Step one of the Yakima system: remove factory rails. Having just spent good money on this truck, I’m not taking off factory rails and adding silicone around the holes to create new mounting points. Innos fits nicely to the factory rails.
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Sierra K.
9/7/2021
The feet shouldnt be on so tight that it indents the roof. We actually have a video of the install on this model vehicle:
Helpful Links
ink872.aspx
inxs200
tv-install-inno-aero-roof-rack-system-2017-toyota-camry-inxb108-2