To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Low-profile, aerodynamic crossbar lets you build an aftermarket roof rack for your vehicle. Aluminum bar has a T-slot that lets you mount channel-mounted carriers and accessories. Rubber strip in T-slot keeps out dirt and won't need trimming.
Features:
Inno Aero Aluminum Load Bar - Black - 48" Long - Qty 1:Specs:
Inno Aero Aluminum Load Bar - Black - 48" Long - Qty 1:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today on our 2011 Kia Sorento, we're gonna be test fitting the Inno Aero roof rack system. That's gonna be part numbers, INXB130-2. And that's gonna be our 51 inch crossbars up top. And then we have our Inno through feet kit. Which is what's connecting our cross bars to our factory side rails. And that's gonna be part number INXS150.As you can see, these crossbars have a nice aerodynamic shape to them.
That's gonna help cut down any type of wind noise or wind resistance when you're driving down the road. What's nice about these crossbars is that, they can be utilized for T-Track accessories.And unlike a lot of systems where you have to pull the rubber strip out, and cut it to length, with this system you simply just push down on the rubber piece right there, and then you can load in your T-Track accessories and then just slide them all the way across. So there's no cutting on your rubber strip needed. I'll put this back on. And once you're done you just put your end cap back on and you're ready to go.If we look at our through feet system, we're gonna see this rubber coated steel strap wraps around the factory side rail, and hooks in under this end cap and it's simply tightened down.
And if we can unlock our end cap, we can take it off. And see this black tab we use to tighten it, or loosen it if need be.And we see these two little black tabs that are hooked on right here, and it secures it to the side rails. And then once you're done, you simply just put the black tab down like that, take your nice end cap, and we can lock it in place. And you will get this set of keys with your roof rack system for security purposes obviously.Now if we come and look at the rest of our kit, and see how it's set up, we see we have our other cross bar right here. We have our two end caps for when we're done tightening it down.
We have our crossbar end caps which we can just put out right before we throw it up there. Then our other Inno through feet rack.So first we're gonna flip this over, we're gonna take our other through feet, making sure that our little tab is facing on the outside, we're gonna take this little black notch and insert it right into this little section right there.So once we do that, we simply just pull it out. And now it can adjust to any length that your side rails might be. Right before we put it on, we can take our end caps and go ahead and throw those on. But you want to be sure you put them on the right side.
So we'll throw these end caps on like that. Now we're ready to install it on our roof.Now to start, we're just gonna set it on top of our roof, and then I'm gonna go over and get our measuring tape, so we can measure how far we want it from out other crossbar. Now how we got this first bar in place, we measured from this little notch right there and our factory side rail, over to the center of the bar. And we measured it even on both sides and then we tightened it down.Now, it doesn't necessarily matter how far apart you have from crossbar to crossbar, it just can't be less than 24 inches. Most of the time I would like to base it off of what kind of accessory I'll be using that day. So we just gotta go over this way a bit. There we go.And this roof rack system can carry a wide variety of products like I said. It can carry anything from kayak carriers, snowboard, and canoe carriers, to even bike racks. Its got a wide variety of uses. There we go.All right, and now I can show you how we tighten it down. So like I said, we're gonna take these two little black tabs on our strap, and set them on these hooks right there. And then we can start tightening it down.Beforehand also, I checked on that side and on this side, you want to make sure that your crossbar overhang is the same so that it doesn't hang over too much. And then once you start feeling some tension in your turning, I like it turn it about five or six more times. There we go. Because we don't want to make it too tight. Let's come to this side, hook it in.And there we go. Now we're ready to go ahead and throw our end caps on, and lock them down. Now we can lock that into place. And now we can see it's secure. And now we're ready to hit the road. But before we do, I do want to give you guys a few quick measurements to give you an idea of how high this is gonna sit off of the roof of your vehicle.First I'm gonna measure from the top of our roof, to the bottom of our crossbar. That's gonna be about 3 1/2 inches of space right there. Now from the top of our roof, to the top of the crossbar, that's gonna be about 4 3/8 inches from the top of our roof.Now as you can see that's plenty of space to utilize any accessories such as bike racks, cargo carriers, stuff like that. It's gonna be plenty of space for them to wrap around our crossbars without scratching or damaging the top of our vehicle.It's also gonna be enough space without impeding our sun roof system if you guys might have one of those. The carrying capacity for these crossbars in 165 pounds, but you want to be sure to double check with your owners manual and make sure that your roof can handle those weights.And that's gonna do it for the test fit of the Inno Aero Roof Rack system on our 2011 Kia Sorento.
Average Customer Rating: 4.8 out of 5 stars (121 Customer Reviews)
Low-profile, aerodynamic crossbar lets you build an aftermarket roof rack for your vehicle. Aluminum bar has a T-slot that lets you mount channel-mounted carriers and accessories. Rubber strip in T-slot keeps out dirt and won't need trimming.We recently purchased 2 kayaks & Thule roof racks from our local outdoor store.
After waiting 2 weeks for our roof racks and J bars to come in we found that the Thule racks did not fit our 2017 Lincoln MKX and they didn't make any racks that would. The vehicle does not have roof racks and has a moon roof.
After a couple of days searching the internet we discovered etrailer.com. We found the Inno roof racks, but still was not sure they would work. We spoke to a repesenative and he assured us that the racks we chose would fit and the Thule J bars we did return would also work. As you can see by the photos 2 days later we were happy Kayakers.
Racks were perfect for my Acura MDX. They fit like a glove and I have used them several times.
I bought these as part of a kit with 60" Aero bars and the appropriate kit for my 14 Flex. I spent probably an hour and a half double checking my measurements and getting them torqued down properly. I spaced the bars on top of the car just a little wider than proscribed because I was planning on carrying 4x8 plywood, and it looked better to my eye. One thing to watch for: The instructions for the car-specific kit (in my case INK263) show the foot spacing measurements for a square bar, and the measuring point for these feet and Aero bars is different. That measurement point is indicated in the instructions for the feet, not the kit. Same numbers, just different reference point. Otherwise, they look good and are rock solid.
worked as expected, I used them to carry my hobie outback kayak (about 100lbs) on my Honda Civic 2016 Coupe (2 doors). They worked with no problem so far (1 year) even under high speed like 70mph.
Great racks. High quality parts. Fit perfectly. Went together easily.
Has worked great for transporting my fishing Kayak as well as small loads of lumber. It has worked fine for about a dozen and a half boards at a time or a couple of sheets of plywood. Just make sure that you have a good way to strap them down as well as maybe a rubber mat to help hold everything in place. The noise from it on the high way can be a lot but certainly not as bad as some that I have heard. I figure that anything on the outside of a vehicle like that will produce some noise.
Started assembly last summer and finally completed installation this spring. Directions took a lot of attention to detail but were adequate. Rack went on car securely and looks great. Have attached kayak rack and a roof pod and both worked flawlessly. Would definitely recommend.
This kit does not fit well. All measurements have been double and triple checked down to the millimeter. The lock on the covers interfere with the hooks. You have to apply so much pressure to get it to close that it makes the rack come loose. Not very satisfied
Noticed box was taped up more then usual, found other manuals that was not specifically for this, and also found one of the feet already had been mounted as there was scratches on the plastic and metal parts
I have had countless bike racks over the years and this is by far the best system I have ever had. Fits like a glove on my F150. Easy to install, looks great and the bikes do not move when on the roof.
I’ve had the system in place for over a year now and haul dual kayaks often! I love it! The only thing I wish I could change is the wind noise that’s comes with it. But I’m sure with any rook rack system you get that.
I did a lot of searching before selecting this rack for my Durango RT (no factory roof rails). It is easy to reinstall once the initial process is followed, I marked my doorjambs with a sharpie and it is easy to set up. Great product!
Great product. Fit perfectly. Went together easily. High quality parts.
Installed incredibly quickly on my 2014 Prius V with some of the best instructions I could have ever asked for. Used the video as well in tandem and got it on the car in about an hour and a half with my partner. It was a lovely experience, which is sometimes difficult for couples to say in situations like this!
There work great and were easy to install. e-trailer rocks and so does Justin.
Installation was a little tricky but once the "feet" were attached to the roof and the bars properly spaced, everything wrapped up very well.
There is no noticeable wind noise with these installed.
It was an easy install with instructions. The rack has held up well so far and looks good on the car.
One was extremely hard to get on compared to the others (not sure if it had some rough machining or something), but once all we’re on, all was good
thanks to Adam for help and competent approach. Adam listened impeccably and in the shortest possible time helped to deliver the goods I needed
Very easy to use
Easy to mount and use. Very sturdy aswell. Measurements are a bit off on width adjustment.
Once I realized which bar was the front one and which was the back it was a fairly easy install. Since the measurements for the foot placement were wrong in the instructions I would suggest not tightening the feet all the way to the bars until you put it on the car. It would have been nice if both sets of rubber pads were the same, with the tunnel hook, and if they had adhesive backing to avoid losing them. I added 2 sided tape.
Good but bad instructions
Tule and Yakima did not have a rack for my Nissan murano. So it was a blessing to find the immo rack. It seems like it can fit any car model. It's strong and secure. I feel my equipment will be safe with this rack.
These feet are easy to use and go well wit the Inno system. I was worried since my car did not come with any roof racks, but this is the solution to haul things on my roof. They work well and are very secure.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.