To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Low-profile, aerodynamic crossbar lets you build an aftermarket roof rack for your vehicle. Aluminum bar has a T-slot that lets you mount channel-mounted carriers and accessories. Rubber strip in T-slot keeps out dirt and won't need trimming.
Features:
Inno Aero Aluminum Load Bar - Black - 54" Long - Qty 1:Specs:
Inno Aero Aluminum Load Bar - Black - 54" Long - Qty 1:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2014 Honda CRV we are going to be test fitting the inno roof rack system. This is going to be consisting of part numbers INXB108-2. Those are going to be the crossbars. Part number INXS200, those are going to be the flush feet. Part number INK413 and that's going to be the clamp that holds it onto your vehicle. We already have the front one installed. You can see it has a nice shape to it.
It looks like it's part of the vehicle. It has a nice aero-dynamic shape which will cut down on wind noise and drag. Let's go ahead and show you how the rear one installs. We already have it partially assembled on our table here. Let's flip it upside down here. The first thing that we're going to do is slide out this portion here on the side of the arm.
Then we will take our mounting plate and put it into position. You will see that it has a little indentation here at the bottom. That's going to fit into the indentation in our little bracket here. Push that back in and then we will load up our foot. This portion here is going to insert into this area here on our bar. Then we will just slide back a little bit and you're going to look into the instructions, because you want a specific measurement in between each foot.
It is going to be different for both the front and the rear. Once we've got it set to where we need it. We'll take the included allen key, go to the bolt on the inside here and tighten that down in place. Then we will take our foot pad and we will install that as well. That just pushes into position. I'm going to flip this around so you can see it a little bit better.
We will remove this screw at the end, then install our clamp. You just want to get it loosely installed so it stays in place. With that done, we can actually set it onto our vehicle. I'm going to go ahead and open up the two rear doors. Then we will set it on. Be careful not to scratch the roof when you do this. If you are a little nervous that you will, just grab an extra set of hands and that will help you out. Now the next thing I'm going to do is get a measurement for the crossbar spread. That's going to be from the center of the front door jam to the center of our bar. Now let's go to the other side and repeat the same process. That looks good. Now we're just going to double check our first measurement, then we can start tightening it down. Now it also comes with the included tool to tighten this down. First we're just going to snug it up right along this edge here. We will do this on both sides and then we'll tighten it down completely. Once we have it snug, give it five or six turns on both sides to make sure we tighten this down evenly. That's not going anywhere. Now we'll take our covers and place those on and lock them up. With that we have installed our inno roof rack system for our 2014 Honda CRV.
Average Customer Rating: 4.8 out of 5 stars (131 Customer Reviews)
Low-profile, aerodynamic crossbar lets you build an aftermarket roof rack for your vehicle. Aluminum bar has a T-slot that lets you mount channel-mounted carriers and accessories. Rubber strip in T-slot keeps out dirt and won't need trimming.Noisy driving down the road. The whistle driving at 60mph is ridiculous and the best part, you can’t even exchange them! Thank you for making me look elsewhere for anything that you sell.
Installation went pretty smoothly. The trick is to fully understand each step before moving to the next. There are a lot of small parts which at first was a little intimidating, but soon I was able to "get with it". I love the finished product and think you helped me get a good deal. Thank you for that
Great fit for my 2023 4Runner and looks amazing.
I was concerned that other brands that clamp to the existing roof rails could pop-off from upward forces due to bumps/wind (I have 2 17’ sea kayaks) - these INNO clamps have a strap that securely holds the bars in place.
Perfect height to be able to get straps/clamps under the bars, but low enough to keep them from hitting my garage door opening.
Great quality and super easy to install.
Waste of money. Most annoying couple hours spent in a long time. Extremely disappointed. Does not fit well. Not exactly a cheap option, but a cheap option in terms of fit and engineering. The instructions online and in the kits do not agree. But there is no helping the design. Plus there are no universal set of instructions--they are all individual items for the fit kit, the bars, etc. But a reasonably inclined person can figure it out so no big deal, but the engineering design is garbage--requires precise measurement yet the design is such that exact measurement is impossible due to the design.
Additionally, the parts are low quality Either low density plastic or easily stripped bolts. Even when as precise as possible, I wouldn't trust it with my kayak. What a mistake. Do yourself a favor and get a Yakima trailer or similar. It isn't that much more money in the scheme of things and then it isn't tied to your car. Can add a hitch to most vehicles anyway.
Installation was a little tricky but once the "feet" were attached to the roof and the bars properly spaced, everything wrapped up very well.
There is no noticeable wind noise with these installed.
One was extremely hard to get on compared to the others (not sure if it was rough machining or something), but once it was on, all was good.
Racks were perfect for my Acura MDX. They fit like a glove and I have used them several times.
Has worked great for transporting my fishing Kayak as well as small loads of lumber. It has worked fine for about a dozen and a half boards at a time or a couple of sheets of plywood. Just make sure that you have a good way to strap them down as well as maybe a rubber mat to help hold everything in place. The noise from it on the high way can be a lot but certainly not as bad as some that I have heard. I figure that anything on the outside of a vehicle like that will produce some noise.
These crossbars are awesome!
worked as expected, I used them to carry my hobie outback kayak (about 100lbs) on my Honda Civic 2016 Coupe (2 doors). They worked with no problem so far (1 year) even under high speed like 70mph.
Easy install on 2021 4runner off road premium. Looks clean, matchs blacked out on white, eadges of chrome cap matches mirror accents and tail lights. Etrailer video was simple to follow. What it didn't show was the foam rubber strips that you put on under the t tracks slot. With cover off and top most flat part of clamp to edge of bar measures about 5.5inches. Make sure the clamp is flush with bar when you measure. Overall looks good
The Inno roof rack fit my 2014 Honda CRV very well. I used it immediately on a 500 mile trip and the rack is fantastic. I connected an XL Thule car box and 11'-6" paddle board to the rack and everything fit fine. The aero design is great and we did not hear any noise during the trip.
We recently purchased 2 kayaks & Thule roof racks from our local outdoor store.
After waiting 2 weeks for our roof racks and J bars to come in we found that the Thule racks did not fit our 2017 Lincoln MKX and they didn't make any racks that would. The vehicle does not have roof racks and has a moon roof.
After a couple of days searching the internet we discovered etrailer.com. We found the Inno roof racks, but still was not sure they would work. We spoke to a repesenative and he assured us that the racks we chose would fit and the Thule J bars we did return would also work. As you can see by the photos 2 days later we were happy Kayakers.
This kit does not fit well. All measurements have been double and triple checked down to the millimeter. The lock on the covers interfere with the hooks. You have to apply so much pressure to get it to close that it makes the rack come loose. Not very satisfied
I bought these as part of a kit with 60" Aero bars and the appropriate kit for my 14 Flex. I spent probably an hour and a half double checking my measurements and getting them torqued down properly. I spaced the bars on top of the car just a little wider than proscribed because I was planning on carrying 4x8 plywood, and it looked better to my eye. One thing to watch for: The instructions for the car-specific kit (in my case INK263) show the foot spacing measurements for a square bar, and the measuring point for these feet and Aero bars is different. That measurement point is indicated in the instructions for the feet, not the kit. Same numbers, just different reference point. Otherwise, they look good and are rock solid.
Installation went pretty smoothly. The trick is to fully understand each step before moving to the next. There are a lot of small parts which at first was a little intimidating, but soon I was able to "get with it". I love the finished product and think you helped me get a good deal. Thank you for that
I did a lot of searching before selecting this rack for my Durango RT (no factory roof rails). It is easy to reinstall once the initial process is followed, I marked my doorjambs with a sharpie and it is easy to set up. Great product!
Well made product with durable components. Fit was good and assembly pretty easy. I would recommend this product.
Great racks. High quality parts. Fit perfectly. Went together easily.
Definite five star….having all glass roof we were handled super, guided from phone to delivery , video to guide are installing, quality product thank you we’ll be back
Started assembly last summer and finally completed installation this spring. Directions took a lot of attention to detail but were adequate. Rack went on car securely and looks great. Have attached kayak rack and a roof pod and both worked flawlessly. Would definitely recommend.
etrailer was the only vendor who had the custom fit roof rack feet I needed for my vehicle. I was trying to put a roof rack onto a Dodge Durango SRT...not a typical vehicle for this accessory! I looked everywhere for a suitable roof rack and thought I was settling by ordering the Inno kit from etrailer. I could not have been more wrong! I am so happy with the purchase!
I have had countless bike racks over the years and this is by far the best system I have ever had. Fits like a glove on my F150. Easy to install, looks great and the bikes do not move when on the roof.
I’ve had the system in place for over a year now and haul dual kayaks often! I love it! The only thing I wish I could change is the wind noise that’s comes with it. But I’m sure with any rook rack system you get that.
It is reasonable price and useful. I wondered whether I should choose aero form type or traditional one. After consideration I choose this traditional square bar for the reason of lower price, So far it is good. I don't feel any noise issue during running. I am satisfied.
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.