To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
These steel, square crossbars attach to Inno feet to create a sturdy roof rack for your vehicle. Elastomer coating resists corrosion and helps cushion your load. Bars accommodate carriers and accessories that clamp around bars.
Features:
Inno Square Load Bars - Black - 54" Long:Specs:
Inno Square Load Bars - Black - 54" Long:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2016 Ford Edge we'll be taking a look at Eno Arrow crossbars. The part number for our crossbars today are INXB115-2, for our flush feet we're using INSS200, and for our custom fit kit for the Ford Edge we're using INK676. These crossbars are a low profile aerodynamic design which will help to reduce wind noise and drag and will allow you to carry any roof-mounted accessories on top of your vehicle. This works with either channel-mounted or clamp-on accessories. The weatherstripping on the inside easily pushes down to adapt for those channel-mounted accessories as well as to help keep dirt, debris and liquid out of your crossbars when you don't have any channel-mounted accessories loaded up. All pieces of the roof rack kit come with a limited lifetime warranty and the crossbars have a 165 pound weight capacity. Here, everything we have on our table is what is included in our kit. We've got our foot pack with our locking cover.
The hardware that the tools that we'll need to secure this to our bar. Our crossbars here. Our fit kit that will be custom for our Ford Edge. The only thing we needed to provide was a flat tape measure. To start our install, we're going to slide this portion here out until it comes all the way out on the end. Then we'll take our metal bracket and we're just going to stick it up underneath and then sliding that piece back in so that it is all in the way in this section here.
That will help us to connect our foot pack to our crossbar. To get our foot pack ready we're going to start by removing our bolt here. We're going to remove the washer with that. We'll take our metal clamp and loosely set that on top and start to tighten down our bolt once again. We don't want to tighten it too much. We still want it to be loose so that we can fit this onto our roof. We'll flip our foot pack over, take our rubber bottom and this is going to secure to the bottom of our foot pack.
Next, we'll take our foot pack and we're going to secure it to the bracket here. Our foot pack is going to slide on top and then slide all the way down to the end of our crossbar. Our measurement for the distance between our two foot packs is going to be 111.5mm. That's going to be from the center of our foot pack to the center of our foot pack. Now we'll take the larger Allen key and we're just going to tighten down the bolt on the inside. This is going to insure that our foot pack stays in this position.
We'll do the same thing to the other side. Now I'm ready to open up our vehicle doors and load this up. I'm going to take our crossbar and make sure that the fatter side is facing towards the front so you get that nice aero shape. We're just going to place this around our vehicle. Now we'll measure our crossbar spread. This is going to give us the correct placement for our rear crossbar. We're actually going to measure from the center of our weatherstrip here between our two doors. Our measurement should be 48mm. We'll measure the other side. With those in place we'll take our included torque tool and we're just going to tighten down this bolt here. We're going to start by tightening it down so that the clamp fits just up against our door jamb here. We'll do the same thing to the other side. Now we'll go back and forth doing about 5-10 turns on each side until it's completely tightened down. When you hear that clicking noise that's when you know you have enough torque behind the bolt and it's completely secured down. We'll do the same thing to the other side. We've got both sides completely tightened down and our door is closed. We're going to take our locking end cover and lock that into place. That's going to help prevent theft and tampering of your crossbars and any channel-mounted accessories that you may have. Now we're ready to load up our gear and hit the road. That's going to be our completed look at the Eno Arrow crossbars for our 2016 Ford Edge.
Average Customer Rating: 4.6 out of 5 stars (368 Customer Reviews)
These steel, square crossbars attach to Inno feet to create a sturdy roof rack for your vehicle. Elastomer coating resists corrosion and helps cushion your load. Bars accommodate carriers and accessories that clamp around bars.Perfect fit for my car, well packaged and detailed instructions. Easy order process and fast shipping. Will buy from etrailer again. Thank you
Worked great! Held up a roof top tent all summer. No bending or damage from use.
This model is not the most stylish and sleek roof rack but its sturdy and made with quality materials. Easy to set up and its even easier to put on the vehicle and take off the vehicle. I only put the rack on my Ford Focus when I go kayaking. Great bang for buck!
Work exactly as described and after a year, still in great condition.
I am writing this review in the context of an owner of a Yakima roof rack system with round crossbars from a vehicle many vehicles prior to the 2021 Hyundai Tucson on which I just installed an INNO roof rack system with the INSUT Feet, INNO NB137 crossbars and 2 INNO INA391 roof bike racks. The INNO crossbars are rectangular in profile, rather than round, but with a grooved top that mates with the INSUT feet, the crossbars should stay firmly put where they are set in the feet. They do not weigh much, but feel pretty solid given their light weight and relatively thin metal walls. One change I would suggest to INNO is to put a factory mark on the center of the crossbars rather than supply a flimsy little decal for the user to measure and place on the crossbars. I never bothered to try to exactly center the round crossbars on my Yakima system, but it is important, at least on the naked roof of the 2021 Tucson, to properly space the feet from the center of the crossbars. I will probably eventually just put a dab of white touch-up paint to mark the center point.
Fantastic customer service.
Andrea is great.
Thanks for your help!
Pretty bendy, could be a bit more solid. But they do the job
Easy to install and very sturdy. Might be more expensive than others on Amazon but trust me spend the money on these.
Been a month haven’t received them yet they are in stock but guess we are waiting for one item which it’s in stock date gets pushed back every day. And the company doesn’t let the customer know the date changes or when they will send it.
Good quality rack system, easy to assemble and install, works well, looks good, fair price, I'm very satisfied with this purchase. I appreciate the guidance I received from William B. at the beginning of my search for a roof rack to carry a canoe on my 2015 Honda Civic. Two thumbs up for this purchase.
Package arrived quick one problem thou blue box inside big brown box which held the roof rack bars was damaged and when i opened it up the rubber end caps are missing is it possible u can send them to me i would appreciate it Thank you
Easy to install and have worked great so far!
Super easy to install and remove. Lock feature is great
Works well, has stayed attached with no issues. We've used them (plus the bars) to keep a canoe and a rocket box on the car at different times throughout the year (not at the same time, it's on a tiny golf).
Incredible engineering: does not feel like an aftermarket rack. Easy to take off if necessary. Solid; highly recommend.
My order just arrived this afternoon and I have not yet looked at everything by I am upset over the rails falling out of the box as it is damaged. I will be looking to make sure all parts are contained but so far not thrilled with the condition of the materials as delivered.
Perfection!!!
Perfect fit.
Worked great! Traveled with a carrier on these racks from Chicago to Seattle. No issues, would buy again!
I have two standup paddle boards that literally live in the racks, and have since day one.
The racks are awesome.
Really great value! No need to spend a lot on Thule. Even those these are square shaped I actually don't hear much road noise. Besides, you're gonna have music playing or riding with the windows down anyway. I would definitely buy these again.
Very noisy, had to take them off when not in use.
Odelia was extremely helpful in helping me choose the right product. I had an end-cap that was missing and she sent me whole package of four. This is the kind of customer support one hopes to receive when deciding to spend a few hundred dollars on a product. I will definitely return to etrailer if I need another car rack for our other car.
I am a fifty-four year old single woman and being able to install these roof racks by myself makes me feel empowered!!
I watched a video emailed with my delivery confirmation of an installation on a similar vehicle all the way through first, and then watched it again as I did the steps myself, pausing when I needed to.
The products appear to be of high quality, were packaged/shipped neatly and it was easy to organize everything for installation. I couldn't be happier!
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.