Kat's Heaters Oil and Coolant Immersion Heater - 120V - 150 Watt - 25 mm NPT
(5 reviews)
Price: $104.63
In Stock
Kat's Heaters Oil and Coolant Immersion Heater - 120V - 150 Watt - 25 mm NPT
Item # KH30924
Our Price: $104.63
In Stock
Need help with installation?
Locate installers near me- All Info
- Reviews (5)
- Q & A (0)
- Videos (1)
- Photos
Kats Heaters Oil Pan Heater - KH30924
- Immersion Heater
- 120 Volts
- 150 Watts
- Kats Heaters
- 25 mm NPT
- CSA Approved
This 3-3/4" long immersion heater submerges in your oil or engine coolant to keep your engine fluid from thickening. The result is easier start-ups, faster heating of your cab, and less wear and tear on your vehicle in cold weather.
Features:
- Ensures smoother start-ups and faster heating and defrosting of your cab
- Installs in oil pan or engine block and submerges in oil or coolant
- Warms engine fluids to increase lubrication and performance
- Keeps fluid from thickening and protects against damage in cold weather
- Pre-heats engine to reduce condensation in the engine block
- Emits less pollution and fewer gas emissions
- Includes removable power cord
- Route through your grille and plug into standard 120-volt AC outlet
- Constructed of durable, rustproof stainless steel
- CSA approved
- Made in the USA
Specs:
- Thread size: 25 mm NPT
- Heating element length: 3-3/4"
- Wattage: 150 watts
- 1-Year limited warranty
Notes:
- Do not use this heater with a 100-percent antifreeze solution.
- Do not start your engine with the heater plugged in.
Start your engine easier and warm your cab faster in cold weather with this immersion heater. Heating your engine fluid keeps it from thickening and freezing, resulting in more reliable start-ups and smoother operation altogether. It also lessens the workload and extends the life of your vehicle's battery. And because starting your engine when it's warm creates less condensation in the engine block than starting it when it's cold, your engine will get better initial fuel vaporization, which causes fewer emissions and less pollution.
This immersion heater installs by screwing into your oil pan or your engine block. The power cord on the heater is removable so that you won't need to buy a whole new heater if the cord gets damaged. The cord can be routed through your grille for easy access to a 120-volt outlet or extension cord. If needed, a longer or shorter cord (sold separately) can be purchased to better fit your application. Make sure the heating element is fully submerged in the oil or coolant before plugging it in.
30924 Kat's Heaters Water and Oil Immersion Heating Element - Removable Power Cord - 120 Volt - 150 Watt - 25 mm NPT - 3-3/4" Long
Video of Kat's Heaters Oil and Coolant Immersion Heater - 120V - 150 Watt - 25 mm NPT
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of Kats Heaters Vehicle Heaters - Engine Oil Heater - KH30924
Jeff: Hello everybody, this is Jeff at etrailer.com. Today we're going to take a look at the Kats Heaters, 120 volt AC oil and coolant immersion heater. Now this part ensures smoother start-ups, faster heating, and even faster defrosting of your cab.Basic of this part we'll install in the freeze plug of the engine block, and submerges in either oil or coolant. The element itself is a stainless steel element. It does warm your engine fluids to increase lubrication and performance, it keeps the fluid from thickening, and it protects against damage in cold weather. It'll preheat the engine to reduce condensation in the engine block, emits less pollution and fewer gas emissions.
It does include this removable power cord right here. You can see if you unscrew this, pull it down, and sort of wiggle it out, you can see that it'll remove with this being installed in your engine block. And then what you can do is route this cord through your grill, and then plug it right into a standard 120 volt AC outlet, and then you just slide the two holes up, push it all the way in, take your nut, and then just go ahead and tighten it down all the way, securing it.And it's constructed of a durable stainless steel on the element we mentioned. It is CSA approved. This part is made in the USA.
Few specs on it. The thread size that this screws into is 25 millimeters NPT threads. The heating element length, this portion right here, is three and three quarter inches. Then a total wattage on this is 150 watts. It comes with a nice set of installation instructions that describes how to install it.But that should do it for the review on the Kats Heaters, 120 volt AC oil and coolant immersion heater..
Customer Reviews
Kat's Heaters Oil and Coolant Immersion Heater - 120V - 150 Watt - 25 mm NPT - KH30924
Average Customer Rating: 4.8 out of 5 stars (5 Customer Reviews)
This 3-3/4" long immersion heater submerges in your oil or engine coolant to keep your engine fluid from thickening. The result is easier start-ups, faster heating of your cab, and less wear and tear on your vehicle in cold weather.by: Chuck 02/11/2021
Works great! I built a preheater out of 1" pipe and used your heater with a tiny thermostat for heating the fuel for my converted hot air furnace which burns used motor oil in my workshop.
by: Bart11/30/2018
we used the device to conduct an experiment in side a gearbox with a new prototype design seal we need the the internal temperature to go to 70 C it was able to do this but it was not able to achieve our 100 C BUT IT PERFORMED IN A MANNER THAT WE WERE HAPPY WITH THANKS FOR THE DEVICE IT HELPED US ACHIEVE OUR GOAL
by: Utah03/15/2019
I have recently purchased this product as an experiment and not for its intended use. I purchased this product to heat oil on a small homemade quench tank. So far so good! I have not been able to get an exact temperature of the oil but it works for what I intended it to be. The slight problem was the threads. If you purchase this product for any fluids under pressure you may have to rechase the threads. I could not find any couplers to fit over the 1” NPT. Where I do not have fluids under pressure I was able to get one full turn out of the threads with no leakage.
by: Okee-Dokee!!!09/10/2020
Hi' I bought this heater for my snowblower motor. (22Hp. twin Briggs & Sratton) I just bought a 1/2" x 3/8" bushing (motor drain plug is 3/8"), 2- 1/2" unions. And there I GO. Thank You! & Okee-Dokee I'm in busness.
by: John04/29/2022
The heater works great. Heated 8 quarts of 50W racing oil to 230deg.F in about 40min. in a dry sump tank.
I need to preheat the straight 50W oil prior to startup on a cold engine.
5
5
See what our Experts say about this Kats Heaters Oil Pan Heater
- Recommended Oil Heater For A 2005 Subaru Outback 2.5Your best bet will be to go with the Kats Heaters Engine Oil Dipstick Heater # KH15200. We do not offer an immersion style heater that will work with your 2005 Subaru Outback. The Dipstick Heater, on the other hand, will be a great fit. Another option is to go with a magnetic heater like the Kat's Heaters Handi-Heat Magnetic Heater # KH1155. The heater itself is 3-5/8" long x 2-1/4" wide and can be attached to the oil pan.
view full answer... - Does Kat's Immersion Heater # KH30924 Have ThermostatYes, the Kat's immersion heater part # KH30924 does have a thermostat.
view full answer...
Do you have a question about this Oil Pan Heater?
Info for this part was:
Edited by:
Lindsey S
Installed by:
Jeff D
Expert Research:
Jameson C
Written by:
Shelly K
Updated by:
Wilson B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.