Customers compare tll9rk to these similar products
Products Featured in this Video
Today on our utility trailer we'll be doing a rehab on the lights. We will be replacing both of the lights, as well as the wiring. We will be using Optronics Submersible under 80" LED trailer light kit with 25' wiring harness, part number TLL9RK. To begin we will need to remove all the existing wiring, as well as any of the old lights that are on the trailer. Now since this is a tilt trailer, we… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
When you test the 4-Way on the Curt T-Connector Wiring Harness, part #56016, at the rear of your vehicle, it should show now power on all 3 pins with the lights off. If you have the vehicle head lights on, you should have around 12 volts at the…
view full answer...The EcoHitch trailer hitch that fits your 2019 Volvo XC60 may interfere with the hands-free liftgate, yes. Most of the time you simply need to kick your foot to the side of the receiver as opposed to the middle and the hands-free liftgate will…
view full answer...We can help you with new lighting and wiring for your 16-foot trailer. A trailer's type, size and weight determine the type and number of lights it must legally have to be compliant with DOT regulations. We have a helpful article that…
view full answer...I recommend checking out our single axle trailer fenders part #HP79VR for a plain fender or part #HP97FR for one with a ridged design. These have a backing plate, measure 28" long x 7-3/4" wide x 10" tall, and fit 13" to 14"…
view full answer...Yes, you can remove your weld-on coupler and install a new bolt-on coupler that fits a 2 inch ball. There is just a few things you need to do to before and when installing. You need to know what channel size and the weight capacity you will need for…
view full answer...The Optronics stud-mounted LED Trailer Light Kit, part #TLL9RK, features left- and right-hand LED light assemblies that are DOT-approved and waterproof, and includes a 25-foot wiring harness, mounting hardware and connectors, and a license plate…
view full answer...I was able to verify that the weight capacity for the Aluminum Car Hauler Ramp Set #288-07503 that you referenced is indeed 6,000 pounds (not kilograms) for the pair and 3,000 pounds per panel. The recommended maximum height of 16 inches is simply…
view full answer...The lid of the Bright Way Trailer Breakaway ICU Kit with 12V, 5-Amp-Hour Battery, Charger, and Wire Loom #BW94FR that you referenced has a wiring diagram shown that details how it wires. Not seen is there is a single wire that runs up to running…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I checked with my Optronics representative, who tells me that the 25 foot long wiring harness included with the #TLL9RK Standard Trailer Light Kit is constructed of 20 gauge wire.
view full answer...There are different taillight requirements for trailers that are over 80 inches in width vs. ones that aren't over 80 inches in width. If you check out the link I attached you will see all of these differenced highlighted. The over 80 inch kits…
view full answer...The trailer itself will have a ground wire from the trailer connector that needs to be attached to a clean and corrosion free bare metal surface on the trailer frame. The lights like in Incandescent Trailer Tail Light Kit, #TL5RK, will ground through…
view full answer...