Customers compare F97CR to these similar products
Products Featured in this Video
What's up everybody. It's AJ with etrailer.com. Today, we're gonna be checking out the Fulton aluminum ball mount. Now these are going to be good for your smaller utility trailers or your boat trailers. You're going to use this with a ball that's sold separately. You'll have to get that.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
I do have one recommendation as your 2022 Land Rover Discovery is not recommended for using a weight and sway distribution hitch. For your receiver it is important to determine how much drop or rise there is between your Land Rover and your 2021…
view full answer...From the base of the #C40047 up to the top of the ball measures 4.091 inches. This is about 1-3/8 inches taller than a standard ball.
view full answer...The only bolt-on swivel jack we have that works with 6" tall trailer frames is the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211. The Trailer Valet has a 500 lb tongue weight capacity and works with frame rails up to 2-3/4"…
view full answer...Yes, there will be an effect on towing capacity when using a hitch extender. The Hitch Extender For 2" Trailer Hitch Receiver part #HE06 for example that you referenced will cut your towing capacity in half, so 1,750 lbs. This will also be the…
view full answer...I attached an FAQ that details how to pick out the correct ball mount. Picking out the correct ball mount will allow your trailer to sit as level as possible. Basically you will first measure the height from the ground to the top of the receiver…
view full answer...Having a ball mount that is longer should not be an issue. It actually can provide more clearance when turning. The standard for a 2 inch ball mount is around 8 to 8-1/2 inches from the center of the hitch pin hole to the center of the ball hole. We…
view full answer...In order to get a ball mount that has effectively 0 inches of rise or drop you would need to get a Trailer Hitch Ball Mount, part #D-4, like the one you referenced that has a 2 inch drop, and then use a 2 Inch High Rise Ball, part #C40034. I attached…
view full answer...For the Yakima Rack and Roll Trailer part #Y08107 the height from the ground to the top of the inside of the coupler where the ball sits is 22 inches so then from the bottom of the coupler lip to the ground measures 20 inches when the trailer sits…
view full answer...The Curt Rockerball Shock Absorbing Hitch Ball has anti-Rotation Plate that is not compatible with all hitch mounts. This hitch ball is recommended to be mounted onto standard ball mounts not shock absorbing ones. I recommend the Curt RockerBall…
view full answer...For your A.R.E. Truck Cap that features the Yakima tracks, you will just need 4 of the Yakima Control Towers #Y8890027, 2 sets of the Yakima Landing Pad #Y00221, and one set of Yakima crossbars, which come in varying lengths. For 58 inch bars use…
view full answer...Most likely the recommendation for the Rapid Hitch Adjustable Ball Mount #AM3410 that was made (it's an old description) to prevent ground clearance of the ball mount when it's in the drop position. Since you'd be using it in the rise…
view full answer...For your 2021 Mercedes-Benz Sprinter 2500 that does not have a factory sway bar your best option is the part #RM-1209-128 with the mount kit part #RM-590064-00. The mount kit is for versions of your vehicle that do not have a factory sway bar and…
view full answer...