Customers compare RM-222-20 to these similar products
Products Featured in this Video
Today we're taking a look at a replacement spacer block. This replaces the spacer block for Roadmaster Tow Bar Quick Disconnects. It works with the Roadmaster Tow Bar Quick Disconnect kit, part number RM-201. The Roadmaster Tow Bar Quick Disconnects car side only, part number RM-222 and the Roadmaster Tow Bar Quick Disconnects Tow Bar side only, part number RM-221. It's made from a durable steel… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
It is feasible this can be done as long as you have the room. The Kenda 4.80-12 Bias Trailer Tire with 12" Aluminum Wheel part #AM30677 that you looked at is 20.7" in diameter compared to a Kenda 4.80/4.00-8 Bias Trailer Tire with 8"…
view full answer...You can replace a 4.80-8 trailer tire with a 4.80-12 or a 5.30-12 trailer tire, but there are a few things to consider before making the change. First, 4.80-12 and 5.30-12 tires are going to have a larger overall diameter than a 4.80-8 tire, by about…
view full answer...The Curt Bumper Brackets #C19748 are a universal fit so you do not have to have a special type of bumper. All that is required is a flat metal section of your vehicle's bumper to install the brackets. You can then tow it with Curt tow bar…
view full answer...I went out to the warehouse and pulled Pins and Thumb Clips #EQ95-01-9415 to measure them for you. The diameter is 3/8 of an inch. The usable length is just under 2-1/2 inches (2.45 inches). And the opening is 2.46 inches by 1.5 inches.
view full answer...The listed price for the Curt Universal Bumper Brackets #C19748 is for the pair. When purchasing this kit you will receive 2 bumper brackets to attach to the vehicle along with the needed hardware. I have attached a short video demonstration that…
view full answer...The 2" Wide Continuous Aluminum Hinge #PLR846 can be cut down and used for virtually any length. The longer that you can leave the hinge the stronger it will be. This hinge will be plenty strong enough for your 65lb storage door on your 2003…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...