Usable Length, Pin Diameter, and Opening Size of Pins and Clips for Equal-i-zer Weight Distribution

Question

Question:

What is the diameter of this pin? What is the usable length and what is the size of the opening? Thanks.

asked by: Harry

0

Expert Reply:

I went out to the warehouse and pulled Pins and Thumb Clips # EQ95-01-9415 to measure them for you. The diameter is 3/8 of an inch. The usable length is just under 2-1/2 inches (2.45 inches). And the opening is 2.46 inches by 1.5 inches.

expert reply by: Michael H

0

click to enlarge

Answer 1

I do have a solution for you. My recommendation is to use the Curt Hitch Receiver Reducer Sleeve - 2-1/2" to 2" #C45405, in combination with the Equal-i-zer Weight Dist Shank - 18" Long - 8" Rise, 4" Drop…

view full answer...

Answer 2

The listed price for the Curt Universal Bumper Brackets #C19748 is for the pair. When purchasing this kit you will receive 2 bumper brackets to attach to the vehicle along with the needed hardware. I have attached a short video demonstration that…

view full answer...

Answer 3

The Curt Bumper Brackets #C19748 are a universal fit so you do not have to have a special type of bumper. All that is required is a flat metal section of your vehicle's bumper to install the brackets. You can then tow it with Curt tow bar…

view full answer...

Answer 4

I don't know what roof rack you have but if you are missing the strip for the crossbars that covers the channels that would be why it's whistling. If you have Rhino Rack Vortex aero bars the part #RRM626 would be what you'd…

view full answer...

Answer 5

You may be experiencing some wear in the suspension components that can cause tire wear and also be a symptom or cause the axle to be misaligned. Inspect your suspension components and if any of the holes where hardware goes is egg-shaped, that…

view full answer...

Answer 6

Seeing as your 2021 GMC Sierra 2500 Denali recognizes the trailer but then shows the error message once you start driving leads me to believe the issue is with your trailer. I would start by checking the 7-way connector and adding Dielectric Grease…

view full answer...

Answer 7

You would not be able to simply replace the spring bars on your Equal-i-zer #EQ37060ET weight distribution hitch. Instead you would need to get both the 1,000 lb tongue weight spring bars #EQ90-01-1099 as well as the 1,000 lb head unit…

view full answer...

Answer 8

I have a few different options for you but the issue with using an electric over hydraulic actuator and factory trailer brake controller together are not particular to any one brand whether that be the actuator brand or brake controller brand, they…

view full answer...

Answer 9

In order to use the Everchill RV Mini Refrigerator part #324-000111 with 12VDC you'll need an inverter, I recommend the Go Power Industrial Pure Sine Wave Inverter part #34282690 which will do a great job of handing the load from the…

view full answer...

Answer 10

Blue Ox has an easy system for determining the weight capacity of your spring bars, whereas other companies may use measurements or printed capacity to assist. With Blue Ox, there is a 5 dimple system: No dimples means it is rated for up to 350 lbs…

view full answer...

Answer 11

The Timbren Kit item #TFR1504E you referenced does fit your 2022 Ford F-150 and can be installed with the RAS kit item #RAS3611-Y that you already have installed. They are not designed to work together though. It will be a tight fit when you are…

view full answer...

Answer 12

Since the 2nd Generation Chevy Silverado (2007-2014 model year) has bare wires under the dash for connecting an aftermarket brake controller instead of a connector, the pigtail included with the #RED44FR Redarc Tow Pro Elite would connect directly…

view full answer...

Usable Length, Pin Diameter, and Opening Size of Pins and Clips for Equal-i-zer Weight Distribution

Product Page this Question was Asked From

Continue Researching