How Many Brackets Are Included with Curt Universal Bumper Brackets # C19748

Question

Question:

not clear on the price, is this $23 per bracket or for a pair?

asked by: Jimmy L

0

Expert Reply:

The listed price for the Curt Universal Bumper Brackets # C19748 is for the pair. When purchasing this kit you will receive 2 bumper brackets to attach to the vehicle along with the needed hardware. I have attached a short video demonstration that will also clarify what all comes with the package.

expert reply by: Chris R

0

Answer 1

The Curt Bumper Brackets #C19748 are a universal fit so you do not have to have a special type of bumper. All that is required is a flat metal section of your vehicle's bumper to install the brackets. You can then tow it with Curt tow bar…

view full answer...

Answer 2

I went out to the warehouse and pulled Pins and Thumb Clips #EQ95-01-9415 to measure them for you. The diameter is 3/8 of an inch. The usable length is just under 2-1/2 inches (2.45 inches). And the opening is 2.46 inches by 1.5 inches.

view full answer...

Answer 3

The distance is 6 inches from the center of the hitch pin hole to the beginning of the gusset for the Blue Ox adapter, which is the following part number: - Blue Ox Adjustable Drop Hitch Receiver Adapter - 2" Hitches - 8" Rise/Drop - 10,000…

view full answer...

Answer 4

You will need a high low adapter since basically it's okay to have up to a 3 inch height difference between the base plate attachment point and the hitch of the RV. Since you are at a 6 inch difference an adapter would be needed. To be level…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Answer 12

The B&W Companion OEM 5th Wheel Trailer Hitch #BWRVK3700 is perfectly compatible with cushioned pin boxes like your MORryde RP072-1621HD, so the clunking you're experiencing isn't related to the two components being incompatible. With…

view full answer...

How Many Brackets Are Included with Curt Universal Bumper Brackets # C19748

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching