Customers compare 115917 to these similar products
Products Featured in this Video
Today we're going to be taking a look at the front hanger for double-eye springs. This hanger provides the attachment point for a leaf-spring. The hanger suspends the spring from the trailer frame. This is configured for use as a front hanger. 1 hanger is included. It's made from a really nice steel construction.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The inner bearings should be #LM48548 (1.375 inch inner diameter), outer bearing should be #L44649 (1.06 inch inner diameter) and the grease seal should be #58846. I would recommend you pull your bearings out to verify that but that SHOULD be what…
view full answer...I'd be happy to help you with that. For starters, the #F008584-2 fenders you'd looked at are designed for 14 inch wheels, you'd be better served going with the #F008585-2 which are designed for 15 inch wheels like the ones you have.…
view full answer...For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…
view full answer...In general the differences aren't huge, but some people prefer spring packs with greater amounts of leaves as that in the unlikely event one of them break there are several others to back it up. But the thinner the leaves (to create a multi-leaf…
view full answer...In regards to the Hopkins Engager Push-To-Test Trailer Breakaway Kit part #20400, there are only two wires with the black being power so it should be run to the positive battery terminal and the blue being brake output so it should be run to the…
view full answer...The hangers that come with the Single-Axle Trailer Hanger Kit for Double-Eye Springs #APS2 that you referenced are wide enough to fit a 1-3/4 inch wide leaf spring as that's what they are designed to fit.
view full answer...For your single axle boat trailer, I recommend the Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear #APS2 along with the 3-Leaf Double-Eye Spring for 2,000-lb Trailer Axles - 23-1/2" Long #SP-113275.…
view full answer...Leaf springs are most often 1-3/4-inches wide but larger widths can also be found, up to 3-inches for very heavy-duty suspensions. We do not offer any leaf springs in a 1-1/2-inch width. It is likely that yours are indeed 1-3/4-inches wide so you…
view full answer...Typically the running light circuit will be noticeably dimmer than the brake/turn signal circuit, so what you described could be normal depending on how dim the lights are. Without seeing how dim the lights are it's hard to say for certain. If…
view full answer...For the assemblies that come with the Submersible, Under 80" LED Trailer Light Kit part #TLL9RK that you referenced the white wires will need to be grounded, the brown wires will run to the running lights circuit, the green wire will run to the…
view full answer...Typically 1-1/2 to 1-3/4 inch diameter axles have 1,000-1,200 lb capacities. Since your axles are smaller than that I can only assume slightly less than 1,000 lbs. On some trailers there will be a plate or sticker that will list the trailer…
view full answer...The trailer will have a plate or sticker on it that will list the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that will list the weight capacity. You can…
view full answer...