Customers compare LC404488 to these similar products
Products Featured in this Video
Hi there, I'm Michael with etrailer.com. Today, we're gonna take a quick look at this Lippert Components Replacement C-Jack. This is going to replace one of the C-jacks for your Lippert Components Electric Ground Control Travel Trailer Leveling System. This is a direct replacement from Lippert, so you can trust it is gonna fit right in place of the original, you're not gonna have to worry about… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
All of the brake hoses, including the main brake line, are made of rubber on the 20 foot Kodiak Hydraulic Brake Line Kit - Tandem Axle #20TA-BLKIT. The hoses on the #20TA-BLKIT also have brass fittings with stainless steel flares.
view full answer...Hey Mike, To determine if the MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR would be a compatible fit you'll first want to measure the bolt hole spacing on your current equalizers. The #MR87ZR has a 6-1/2" center to center…
view full answer...I have a weight distribution system that will work with your 2023 Ember Overland Series 201FBQ travel trailer but there is not going to be enough room on your coupler for the B&W Continuum item #BW28FR. That jack is directly in the way. It looks…
view full answer...The weight distribution system I recommend for your trailer and Cadillac Escalade is the Strait-Line Weight Distribution System w/ Sway Control - Trunnion Bar - 10,000 lbs GTW, 600 lbs TW #RP66082. The vintage style of your trailer is more prone to…
view full answer...The two metal plates on the clamp-on bracket for the Blue Ox SwayPro Weight Distribution System like part #BXW0750 should not be separating. Since the brackets are separating you will need to replace the clamp for which we have the Clamp-On Lift…
view full answer...The Replacement C-Jack for Lippert Components Electric Ground Control TT part #LC404488 does not include the wiring harness but rather the pigtails that you will need to plug into your existing wiring harness. The wiring harness however is not a…
view full answer...I would start by checking location 74 which is the relay for the trailer tow left-hand stop/turn function. Another place to check is location 100 which is the trailer tow turn signal function. You could also check location 70 which is the trailer tow…
view full answer...Yes, they will fit. When measuring the door way, you will measure from the widest part on the inside of the door frame to the opposite sides widest part of the door frame. So with your 25-1/4" measurement, the SolidStep Manual Fold-Down Steps…
view full answer...The SolidStep Manual Fold-Down Steps part #LC791572 will fit a door way from 25" -28.9" wide when measuring the frame inside. If the factory label sticker shows a doorway width between 26"-29" then the above steps will work for…
view full answer...The MORyde Rubber Equalizer #MR87ZR could absolutely be used on an enclosed trailer. The 8K rating would be per axle. It might be more accurate to say that these equalizers can be used on axles 8K and under. So if your trailer is 10K gross weight, a…
view full answer...Yes it does, what you will need are 1/2"-20 self-tapping bolts in order to install the bracket you asked about: - Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 #LC349975
view full answer...Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
view full answer...