Customers compare T2336100042 to these similar products
Products Featured in this Video
Hello neighbors, Steven here with etrailer.com. Today we're looking at this replacement master cylinder for your Dexter Aero 7500 Brake Actuators. This does only work with the drum brake models only folks, so very simple. Again, a replacement master cylinder, all the screw holes here to mounted everything. The nice rubber boot here on the end I'll move that boot back on. I'm gonna leave… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Hey Tim, thanks for the picture of your current brake assemblies. While what you have doesn't look exactly like a free-backing setup you definitely can replace what you have with them. For that I would go with the etrailer part #AKFBBRK-35 which…
view full answer...Based on the information you provided either the Titan Hydraulic Brake Kit - Free Backing - 10" - Left and Right Hand Assemblies - 3,750 lbs #T4071600-500 or #T4423500-400 will fit your drums. The only difference between these two brakes is the…
view full answer...What it sounds like is happening with the Dexter Hydraulic Brake Kit - Free Backing - Galphorite - 10" - Left/Right Hand - 3,750 lbs #T4423500-400 locking up when wet is the shoe has likely absorbed moisture and expanded, causing the lock up.…
view full answer...To determine the correct brake kit you'll need to measure the diameter of the brake pads (from one side of the assembly to the other). If it is 10" and you have hydraulic brakes then I recommend the Titan Free Backing Kit #T4071600-500, but…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…
view full answer...Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…
view full answer...Hi Larry, So we have a couple bumpers that may work, though each is 96 inches long. They can be cut to length though, and the difference is their width, as one is 3" wide and the other 4" wide to fit different size bumpers: - Pre-Drilled…
view full answer...Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…
view full answer...Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…
view full answer...