Customers compare C45901 to these similar products
Products Featured in this Video
Speaker 1: Today we're going to take a look at the Curt Channel Style Adjustable Ball Mount, has a 6,000 pound weight capacity. Now this is designed to mount on trailer hitches that have a two inch by two inch receiver tube opening. You notice this is an adjustable channel mount, which will allow for precise trailer leveling. There's six rows of holes here and each one is one inch… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The average trailer coupler height is in the neighborhood of 16-19 inches. What I'd recommend you do is put the various trailers you tow up on their jack so the frame is level to the ground, and measure their coupler height (see linked article).…
view full answer...The ball measures 2-3/4 inches from the ball mount surface to the top of the ball. I am glad to see that you are making sure you get the proper ball mount for your tow set up. The rule of thumb is to be no more than 2 inches over or under. The…
view full answer...To use the Curt Echo Wireless Trailer Brake Controller #C51180 your vehicle only needs 12 volt, ground, and turn signals connected to its 7-way socket. What this means is you do not need the brake signal from the 7-way. For example, if you used a…
view full answer...An 11 inch long ball mount is on the longer side but not long enough that it would it diminish the towing capacity of your Toyota Highlander. If were to go much beyond 11 inches I would begin to worry that maybe the leverage would be too much but for…
view full answer...I assume you are wanting to add an in line fuse to a 12V power circuit running from your vehicle battery to the trailer connector on your vehicle. There are a few things to consider before adding an in line fuse to a 12V power lead to a trailer…
view full answer...Most trailer hitch balls have a flat part on two sides of the base like the 2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000 #A-90 for example. You will simply need a open end wrench large enough to fit that. Vise…
view full answer...Yes, the RockerBall and channel style ball mount you asked about are absolutely compatible: - Curt RockerBall Shock Absorbing 2" Hitch Ball #C40047 - Curt Channel Style Adjustable Ball Mount #C45901 The reason is, the ball mount accepts a hitch…
view full answer...When the platform of the Curt Channel Style Adjustable Ballmount #C45901 is in the drop position but up in the highest position possible the drop is right at 2 inches. I attached a review video for this ball mount for you to check out as well.
view full answer...From the base of the #C40047 up to the top of the ball measures 4.091 inches. This is about 1-3/8 inches taller than a standard ball.
view full answer...I made a picture showing 3 important measurements on the Draw-Tite adjustable ball mount #7390. The distance from hitch pin hole center to ball hole center is 11-3/4 inches. If the extra 2 inches is needed in a ball mount then of course it would be…
view full answer...No, all of the BOLT locks like the BOLT Trailer Hitch Receiver Lock for 2" and 2-1/2" Hitches #BLT99FR you're looking at are coded to the vehicles key - there are no options that just use a regular key. You could just use a standard…
view full answer...The trailer hitch for a 2015 Lexus RX 350 is not the same as a trailer hitch for a 2019 Lexus RX 350 because there was a generation change in 2016. Therefore, you will need a new trailer hitch for which we have the Curt Class III Receiver Hitch part…
view full answer...