Best Trailer Hitch Option for 2008 Honda Pilot That Doesnt Involve Trimming Bumper Fascia
Question:
i have 2008 honda pilot .i want to install the curt receiver hitch because of the extra bumper support but i do not want to do any facia trimming will it work on my model.without any modifing thanks
asked by: Pk
Expert Reply:
When we installed the Curt # 13328 on a 2008 Honda Pilot, we didn't need to trim the bumper fascia, as shown in the video I've linked you to. If your bumper fascia is the same as shown in the video, you shouldn't need to trim anything.
The Draw-Tite # 75599 has the same towing and tongue weight capacities, so it's just as strong and would work just as well as the Curt model. The Draw Tite model makes no mention whatsoever of the need for trimming the bumper fascia, which is why it would be my choice.
If you'll be towing with your hitch, you might also need the following to complete your towing system.
Ball mount, part # D-4
Hitch Pin and Clip, # PC3
Trailer Wiring Harness # 118336
2 inch trailer ball, part # 63845
1-7/8 inch trailer ball, part # 19260
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How Much Does the Curt Hitch 13328 Weigh and How Large is the Shipping Box?
- Q&A: Trailer Brake Controller Fuse Location on 2015 Ford F-150
- Q&A: Recommended Hitch for a 2024 Honda Pilot
- Article: How to Choose the Right Trailer Hitch Class
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Trailer Hitch Recommendation for 2003 Honda Pilot
- Article: Trailer Wiring Diagrams
- Q&A: Fix For Curt Echo Wireless Brake Controller Locking Up Trailer Brakes At Low Speeds
- Q&A: Troubleshooting Titan BrakeRite Electric Over Hydraulic Trailer Brake Actuator-Won't Build Pressure
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Will etrailer Trailer Hitch e98851 Work With Full Sized Spare Tire On 2004 Acura MDX?
- Article: Flat Towing Package for 1998-2006 Jeep Wrangler
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com