Recommended Scissor Jacks for a 2021 Winnebago Micro Minnie

Question

Question:

What scissor jacks can i buy for my 2021 winnebago micro minnie 2100bh that will be compatible with the SnapPad SnapJack SJ RV Scissor Jack Pads - Qty 4 I just bought?

asked by: Robert G

0

Expert Reply:

The Scissor Stabilizer Jacks w/ Handle item # TJSCHD-24-4 would work great with both your Micro Minnie and the SnapPad SnapJack SJ RV Scissor Jack Pads item # SN32FR you purchased. These have a 10,000 lbs total capacity and expand from 5" to 23-3/4".

I have linked a review video below so you can see them demonstrated.

expert reply by: Jerred H

0

Answer 1

The spacing between the mounting holes on the SnapPad SnapJack for RV Scissor Jack Stabilizers #SN65FR is approximately 1-7/8".

view full answer...

Answer 2

I tested a few wheels that we have in stock and found that the #JC-102 would physically fit on the Lippert Quick Drop Tongue Jack #LC733926, but would limit your capacity down to wheel's at 1,200lbs.

view full answer...

Answer 3

The distance between the bolts on the SnapPad SnapJack for RV Scissor Jack Stabilizers #SN45FR is 2" on center which is the standard. The same is true for the higher rated #SN65FR. If you want to use these with your scissor jacks the only…

view full answer...

Answer 4

The Scissor Stabilizer Jacks w/ Handle item #TJSCHD-24-4 would work great with both your Micro Minnie and the SnapPad SnapJack SJ RV Scissor Jack Pads item #SN32FR you purchased. These have a 10,000 lbs total capacity and expand from 5" to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 8

I am sorry but we do not have an AC cover with those dimensions. The closest option we have is the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners item #AT3308046006 which measures 40-1/2" long x 29"…

view full answer...

Answer 9

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 10

Hey Dan, The ground for the Roadmaster Brake-Lite Relay Kit for Towed Vehicles #RM-88400 typically gets tied into the ground for the braking system to intertwine them so that they're active at the same time. When used to prevent turn signals…

view full answer...

Answer 11

There's unfortunately not a guide to tell us the sizing of your trailer's jack pads so you'll want to measure and note the shape of each pad. I've run into numerous situations where the front and rear pads were either different sizes…

view full answer...

Recommended Scissor Jacks for a 2021 Winnebago Micro Minnie

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching