Compatible Wheel For A Lippert Quick Drop Tongue Jack # LC733926

Question

Question:

Can I use a wheel with this jack instead of the included footpad?

asked by: Bob G

0

Expert Reply:

I tested a few wheels that we have in stock and found that the # JC-102 would physically fit on the Lippert Quick Drop Tongue Jack # LC733926, but would limit your capacity down to wheel's at 1,200lbs.

expert reply by: Kevin C

0

Answer 1

The spacing between the mounting holes on the SnapPad SnapJack for RV Scissor Jack Stabilizers #SN65FR is approximately 1-7/8".

view full answer...

Answer 2

The Scissor Stabilizer Jacks w/ Handle item #TJSCHD-24-4 would work great with both your Micro Minnie and the SnapPad SnapJack SJ RV Scissor Jack Pads item #SN32FR you purchased. These have a 10,000 lbs total capacity and expand from 5" to…

view full answer...

Answer 3

The distance between the bolts on the SnapPad SnapJack for RV Scissor Jack Stabilizers #SN45FR is 2" on center which is the standard. The same is true for the higher rated #SN65FR. If you want to use these with your scissor jacks the only option…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Compatible Wheel For A Lippert Quick Drop Tongue Jack # LC733926

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching