Replacement Hub and Spindle for TDE 11033 Hub

Question

Question:

I have a 1992 Stratos bass boat single axle the spindle and hub is broke the 5 lug hub has a part #11033 T.D.E. the spindle has a round shaft 1 and 3/4 that is welded on and looks to be maybe 6 and 3/4 or 7 inches long wondering if you have a complete spindle and hub assembly that will work looking to buy 2

asked by: Philip M

0

Expert Reply:

The Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles like the # AKIHUB-545-35-K. Then for a spindle the part # TRU84FR that you referenced would be what you need.

expert reply by: Jameson C

0

Answer 1

From what I was able to find out from my research, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles. Replacement hubs that have these specs typically use a #L68149 inner bearing and #L44649…

view full answer...

Answer 2

I believe we can narrow this down based on the information you are referencing. However, the best way to be sure is to measure your existing bearings or spindle with a digital caliper like the #PTW80157. It looks like one bearing is stamped with…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

We may have a grease seal that will work in your application however, my research had conflicting measurements for the Hadco 3122 that you referenced. I contacted my technical contact at Redline to verify that the Redline Grease Seal #1105-100-031…

view full answer...

Answer 10

I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting.

view full answer...

Answer 11

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 12

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

Replacement Hub and Spindle for TDE 11033 Hub

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching