Troubleshooting Lower Suspension Height On a 371 Fuzion 5TH Wheel Toy Hauler With MORryde CRE3000

Question

Question:

Hello I have a 371 Fuzion - My tires are the factory tires per label on nameplate The tires have like no clearance from the fenders Would you guys sell al lthe parts need to do a refresh to stock and or would you guys sell any parts to potentially lift it an inch or so I am seeing wear on the tires from hitting the fenders Also If you look at the attached photo looks like the rubber is pushed out but I dont know if that is normal or not Something is off and I cant necessarily point finger to it Any recommendations ?

asked by: Ian R

0

Expert Reply:

It is normal for the rubber to push out of your MORryde Shock Absorbing Suspension Equalizers # MR27ZR the way it is. The main issue I see is your Shackle Strap # TRSL313 is wearing out. I can see a bit of the hole on the top left strap which means the holes in the strap are being elongated. I recommend replacing these immediately with one of the following kits.

MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" # MR46ZR
MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 3-1/8" # MR76ZR
MORryde Suspension Upgrade Kit for Tandem Axle Trailers w Correct Track - 2-1/4" # MR58ZR
MORryde Suspension Upgrade Kit for Tandem Axle Trailers w Correct Track - 3-1/8" # MR98ZR

You will want to measure your existing straps from center of mounting hole to center of mounting hole to verify which is the correct size for you. The Correct Track kits are for those which have adjustable mounts on the front and rear hangers. If you are unsure if you have this please send me an image of your other hangers.

As far as the height goes it does look like your springs are beginning to flatten out due to the weight. The SumoSprings Trailer Helper Springs # SS26MV may be able to help you raise the suspension back to a more normal ride height. Otherwise you can start by replacing the leaf springs and if more height is still desired we do have the Lift Kit # RR23QX which will allow you to raise your suspension by 1-1/4" or 2-1/4".

expert reply by: Bud M

0

Equalizer on a 371 Fuzion 5TH Wheel Toy Hauler
(click to enlarge)

Answer 1

Okay let's get started here with the suspension for your 2012 Skyline Koala 27CDS with 3,500 lb Axles; for the first part regarding your equalizers and suspension upgrade kit, so long as your current equalizer is spaced 6 inches (or close to it -…

view full answer...

Answer 2

I do have a lift kit that is compatible with a Keystone Montana in the Correct Track Trailer Alignment and Lift Kit part #RR23QX. This kit attaches to the leaf spring hangers and extends them to provide lift of 1-1/4" or 2-1/4". This is the…

view full answer...

Answer 3

In general you want 4 to 6 inches between the top of the truck's bed rails and overhang of the trailer. You also need to be sure that the trailer is also sitting level too. Sometimes in order to have the correct bed rail clearance the nose of the…

view full answer...

Answer 4

Since your axles are already flipped you don't have many options for a lift. Although it is not going to get you 4" you can use the Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX. This will get you an additional…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 10

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 11

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 12

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...