2" Receiver Adapter Recommendation for 20x47 Reese Cargo Carrier with 1-1/4" Shank

Question

Question:

I have one of these cargo carriers: 63155 My new car has a 2 hitch, what is the recommended adapter to use with this carrier?

asked by: John R

0

Expert Reply:

Thanks for reaching out!

To use the 20x47 Reese Cargo Carrier # 63155 with the 1-1/4" shank with the 2" receiver on your 2021 Subaru Outback Wagon I recommend using the Trailer Hitch Reducer # e63YR because it won't reduce the weight rating of your hitch receiver like a lot of other options would.

In addition to this I also recommend picking up the etrailer Hitch Receiver Lock # e98881 and etrailer Anti-Rattle Hitch Stabilizer # e99007 to help stabilize and lock the adapter to your receiver.

Attached are some review videos for you to check out!

expert reply by: Jon G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The best hitch for a 2024 Subaru Outback is the etrailer item #e25TR. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 350 lbs…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 7

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to replace the Advent Analog Wall Thermostat ACTH11 you'll need the Air Distribution Box w/ Wall-Mounted Thermostat for Advent Air RV Air Conditioners part #ACRG15. This is a digital style replacement which is what you'll need since…

view full answer...

Answer 10

For your 4x6 utility trailer, I recommend using the Taskmaster 4.80R12 Radial Trailer Tire part #TT48012C. This tire has a radial ply construction which will be better for the longer highway trips you intended to make. It has a load range C rating…

view full answer...

Answer 11

Thanks for the picture of what you have and the info you listed. The correct wheel you need is the part #AM20794 that you referenced.

view full answer...

Answer 12

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...

2" Receiver Adapter Recommendation for 20x47 Reese Cargo Carrier with 1-1/4" Shank

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching