What Is The Weight Difference Between The Steel And Aluminum Brophy Truck Camper 4 Step Models

Question

Question:

What is the weight of the aluminum 24” stairs ? And what is the weight of the steel stairs both would be the 4 step models ?

asked by: Roger P

0

Expert Reply:

Great question.

The Brophy Camper Scissor Steps - 4 Steps - Aluminum - Diamond Tread - 17" Wide - 250 lbs # AS04 weigh in at 21 pounds.

The Brophy Camper Scissor Steps - 4 Steps - Steel - Diamond Tread - 17" Wide - 275 lbs # SS04 weigh in at 34 pounds.

expert reply by: David B

0

Answer 1

Hey Mark, thanks for the question, and while we have exactly what you're looking for, it's actually a different part number (the one you mentioned is for a long bed). I went ahead and verified for you the correct SuperHitch for your 2018…

view full answer...

Answer 2

I went out to our warehouse to take a few measurements on the mounting bracket for the Brophy Camper Scissor Steps #AS24. The base bracket profile measures 24 inches long, 1 inch tall, and 1 inch deep. The shorter tabs that will be closer against the…

view full answer...

Answer 3

The RoadActive Suspension Custom Leaf Spring Enhancement Kit #RAS4611 would provide a slight upgrade in the sense that it would provide you with a set-it and forget-it option that wouldn't require you to connect and disconnect when you hook up…

view full answer...

Answer 4

When installing the TorkLift StableLoad Rear Suspension Upgrade with Quick-Disconnects #TLA7310 the important thing is that the kit allows the overload spring to engage properly with the rest of the spring pack. If you have to use a different amount…

view full answer...

Answer 5

Overall height is 5-3/16 inches. That means that once installed, the double convoluted springs from the Timbren SES Kit, #TGMRCK25D, will sit 5-3/16 inches below the jounce bumper holder on the frame. The outer diameter of these springs is 4-5/16…

view full answer...

Answer 6

The lateral angle of the Torklift StableLoads part #TLA7310S is designed to make engaging the system a bit easier, but as you can see in the picture I attached when they are engaged the support is across the entire overload spring. I also attached a…

view full answer...

Answer 7

You wouldn't need to jack the truck up to engage and disengage the Stableloads like part #TLA7310. There shouldn't be enough load in the suspension of the truck to cause the StableLoad to not be able to engage/disengage. Now if your truck was…

view full answer...

Answer 8

The overall height of the Timbren Spring Kit part #TGMRCK25D is 6-1/4 inches.

view full answer...

Answer 9

I am not personally a huge fan of the TorkLift StableLoad Suspension Upgrades part #TLA7310 and #TLA7202 as you have come to find out they don't always provide the most support but I am a big fan of the Timbren Rear Suspension Enhancement System…

view full answer...

Answer 10

I spoke with my contact at TorkLift and he informed me that if you wanted to just engage the front or the rear of the part #TLA7310 you could. He said that what you are planning on doing is perfectly fine and would work well for you.

view full answer...

Answer 11

I wouldn't say that the TorkLift StableLoad Suspension Upgrade w Quick-Disconnect #TLA7310S takes the place of an airbag system and they can definitely be used together with a system like the Firestone Ride-Rite Air Helper Springs #F35FV. This…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...