Customers compare SS04 to these similar products
Products Featured in this Video
Speaker: Today, we're going to be taking a look at the Brophy Scissor Steps. This is a 4-step design. These steps are designed for applications with a vertical height measurement from 31 inches to 40 inches. The vertical height is the measurement from level ground to the placement of the included mounting bracket. This is going to be the included mounting bracket. This would mount about 1/8 of an… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
It is too small of a space to fit the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 4 Steps - 375lbs - Black Bracket Item #TLA7834 but you can instead mount it to the bumper of your camper like in the attached picture.
view full answer...When a camper is loaded on a pickup truck bed there will be a gap between the truck bed rails and the underside of the camper as you show in your photo. No worries there. For your camper tie-downs, it loos as though you have attached the rear ones…
view full answer...Sounds like you'd want to go with a removable scissor setup like the Brophy Camper Steps part #AS24 which will need to be taken off it's mounting bracket between uses. This will give you total access to your trailer hitch when…
view full answer...The Brophy Camper Scissor Steps - 4 Steps in aluminum, #AS04 has a shipping weight of 21 lbs. The Brophy Camper Scissor Steps - 4 Steps - Steel, #SS04 is 34 lbs.
view full answer...I've attached some dimensions below to help you determine fitment of the Brophy Camper Scissor Steps #AS24 with your truck bed camper. The mounting bracket is 24" long x 1" tall (1-3/8" tall if you include the…
view full answer...I went out to our warehouse to take a few measurements on the mounting bracket for the Brophy Camper Scissor Steps #AS24. The base bracket profile measures 24 inches long, 1 inch tall, and 1 inch deep. The shorter tabs that will be closer against…
view full answer...I spoke to TorkLift about the issue you're having with the TorkLift GlowStep Stow N' Go Scissor Steps part #TLA7834 and they informed me to inform you to tighten the hinge tension on the side that's sagging. I have attached…
view full answer...If you're having trouble getting access into the bumper when installing the TorkLift GlowStep Stow N' Go Scissor Steps part #TLA7834 you'll simply need to drill an access hole large enough to fit the bolts through and then you can use a…
view full answer...Thank you for all of the details! The correct tie-downs for your 2018 Ford F-150 include the following: Front - #TLF2020 Rear - #TLF3007 I've attached review videos for you to check out.
view full answer...The smaller version 16x21 TorkLift Lock and Load SideKick Cargo Tray #TLA7901 has inside dimensions of 21-1/4" long, 16-1/8" wide, and 3-15/16" tall. Since your Predator 3500 generator measures 22-3/4" long and 17-1/3" wide,…
view full answer...The bracket of the Aluminum Scissor Steps #AS04 that you referenced stays attached to the camper, but the steps themselves get removed while traveling. Check out the review video I attached for these steps as well.
view full answer...I contacted the manufacturer regarding the installation of the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR. They were able to provide me with a wiring diagram which I have included here for you.
view full answer...