Troubleshooting Brakes Pulsing with Blinkers with Demco SBS Stay in Play System
Question:
I installed a stay and play system to my 2012 jeep wrangler. Now when I use my MH turn signal the brakes pulse. I have looked on line and it said I needed to have a diode added to my system but i also looked on your etrailer expert section and they say my battery needs to be disconnected. can you tell me which of these i should try?
asked by: Chester E
Expert Reply:
I recently asked Demco about brakes pulsing with the install of the Demco SBS Stay in Play part # SM99251 and they said this was normal if the sensitivity was cranked up too high and near the max setting. Have you set the sensitivity setting of your setup yet.
Product Page this Question was Asked From
Demco Stay-IN-Play Duo Flat Tow Brake System for RVs w/ Hydraulic Brakes - Proportional
- Tow Bar Braking Systems
- Brake Systems
- Proportional System
- One Time Set-Up
- Fixed System
- Power Assist Brake Compatible
- Hydraulic Brakes
- Demco
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Vehicle Tow Bar Wiring
- Shop: Roadmaster High-Low Adapter for Tow Bars - 2" Hitches - 6" Rise/Drop - 6K GTW, 200 lbs TW
- Video: Roadmaster Nighthawk All Terrain Tow Bar Road Test
- Video: Roadmaster Nighthawk All Terrain Tow Bar Installation - 2012 Honda CR-V
- Video: Roadmaster Nighthawk All Terrain Tow Bar Review rm-676
- Shop: Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights - Non-Binding - RV Mount - 8,000 lbs
- Shop: Roadmaster High-Low Adapter for Tow Bars - 2" Hitches - 6" Rise/Drop - 10K GTW, 400 lbs TW
- Shop: Hopkins Custom Tail Light Wiring Kit for Towed Vehicles
- Video: Hopkins Tail Light Wiring Kit Installation - 2014 Honda CR-V HM56304
- Shop: Vehicle Tow Bar Brake System
- Q&A: Troubleshooting Pulsing Brakes With The Demco Stay-In-Play Braking System While Turn Signal Is On
- Q&A: Demco Stay-IN-Play DUO Pulsing On/Off When Turn Signal Is Activated
- Shop: BOLT brand vehicle and hitch locks
- Video: SMI Stay-IN-Play DUO Braking System Installation - 2014 Honda CR-V
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 4-Pole Flat Connectors
- Shop: BOLT Trailer Hitch Receiver Lock - 2", 2-1/2", and 3" Hitches - Ford Side-Cut Key
- Shop: Demco Stay-IN-Play Duo Braking System for RVs w/ Hydraulic Brakes - Wireless Monitor - Proportional
- Video: Roadmaster Tow Bar Wiring Kit Installation - 2014 Honda CR-V
- Video: Roadmaster Universal Diode Wiring Kit Installation - 2014 Honda CR-V
- Q&A: Troubleshooting 2014 Jeep Wrangler Brakes Pulsing With Motorhome Turn Signals
- Q&A: 2014 Honda CR-V Flat Towing Preparation Steps
- Q&A: No Brake Lights With Ignition Off Using Roadmaster Brake-Lite Relay Kit On a 2010 Honda Fit
- Q&A: If Taillights of Vehicle are Bypassed for Tow Bar Wiring is a Brake Light Relay Required
- Q&A: How to Find the Cold Side of a Brake Light Switch
- Article: RV Sway Control, Stabilization, and Suspension Enhancement
- Shop: Vehicle Sway Bars
- Shop: Roof Rack
- Shop: Trailer Hitch
- Search Results: tow bar
- Article: Trailer Wiring Diagrams
Don L.
11/13/2021
I have the same issue after the sensitivity has been adjusted.