Dimensions Of Curt 31408, Draw-Tite 65080, and Draw-Tite 64079 Front Mount Trailer Hitch Receivers
Question:
I would like to put a front hitch on a car that is not covered. Instead of fabricating this from scratch I would prefer to start with one of your hitches and modify it, but picking one is hard without dimensions. Can I get dimensions on 31408, 65080,and 65079? Thank you. BTW the car is a 02 kia sportage 4x4 and I just want to move small boats and put a home snow plow on it.
asked by: Sam
Expert Reply:
I had our warehouse measure each of the front mount trailer hitch receivers you mentioned, and the dimensions are as follows.
The Curt # 31408 measures 32-3/4" long x 8-3/4" wide, the Draw-Tite # 65080 measures 36-3/4" long x 10-3/4" wide, and the Draw-Tite # 65079 measures 31-3/4" long x 9-1/2" wide, which you can see in the included diagrams.
Each of these options will require fabrication as you know, since none of them are confirmed to fit your 2002 Kia Sportage 4x4. I recommend checking with the owner's manual of your vehicle to make sure the front end of your Sportage can support the weight you of the snow plow or small boats you mentioned.
Products Referenced in This Question
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Front Receiver Hitch
- Custom Fit Hitch
- Front Mount Hitch
- 350 lbs Vert Load
- 9000 lbs Line Pull
- 2 Inch Hitch
- Square Tube
- CURT
more information >
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Front Receiver Hitch
- Custom Fit Hitch
- Front Mount Hitch
- 500 lbs Vert Load
- 9000 lbs Line Pull
- 2 Inch Hitch
- Square Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Front Receiver Hitch
- Custom Fit Hitch
- Front Mount Hitch
- 500 lbs Vert Load
- 9000 lbs Line Pull
- 2 Inch Hitch
- Square Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Front Mount Hitch
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Search Results: hitch extender for bike racks
- Q&A: How to Determine the Location of the Receiver for a Front Mount Hitch on a 2011 Toyota Tundra
- Video: etrailer Trailer Hitch Reducer And Extender Review
- Shop: Trailer Hitch Reducer and Extender - 2-1/2" to 2" Trailer Hitch - 7" Long
- Search Results: front bumper bike rack
- Search Results: kuat
- Shop: Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Video: Demco Spare Tire Carrier Review
- Video: Curt RV and Camper Hitch - Bumper Mount - E-100 Review
- Video: Review of Demco Spare Tire Carrier - Trailer Tongue Mount Silver - DM15851-52
- Video: Review of Ultra-Fab Products RV and Camper Hitch - RV Bumper Mount Hitch - UF35-946402
- Video: Stromberg Carlson 2 inch Motor Home Hitch Review
- Shop: Stromberg Carlson 2" Motor Home Hitch Receiver for RV Bumpers - 200 lbs
- Shop: Ultra-Fab 2" Motor Home Trailer Hitch Receiver for 4" x 4" Bumpers - 3,500 lbs
- Q&A: How Does the Draw-Tite Front Hitch # 65048 Install on a 1997 Jeep Wrangler TJ
- Q&A: Dimensions of Curt Front Hitch 31408
- Shop: Trailer Hitch
- Q&A: Is there a Front Receiver Hitch for a 2022 Toyota Tundra?
- Video: Front Mount Trailer Hitch Installation - 2014 Toyota Sequoia - Curt
- Q&A: Distance From Hitch Tube To Receiver of Draw-Tite Front Mount Hitch For 2020 Toyota Tundra
- Q&A: Comparing Curt and Draw Tite Front Hitches for 2018 Toyota Tundra
- Q&A: Is Skid Shield Trimming Required if Door is Present to Access Oil Filter on 2021 Toyota Tundra
- Search Results: front receiver hitch
- Search Results: front hitch
- Search Results: universal front mount hitch
- Search Results: rhino rack fishing rod holders