Distance from Mounting Surface to Hitch Crosstube on Curt Hitch # C13701

Question

Question:

What is the distance from chassis mount bolt holes down to the crossbar for the 701 and 702 ? 2 inch ?. I need to keep the 2 inch receiver opening up as close to the chassis rails as possible. 1997 Ford f53, this coach has a history of butt draggin. Also will your skid rollers fit the crossbar that will extend out past the mounting plates, I wont be cutting the ends off.

asked by: Vince B

0

Expert Reply:

I spoke to my contact at Curt to get the measurements you requested. He said that from the top of the cross tube to the top of the mounting plate the Curt hitch # C13701 measures 1-1/2 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Thanks for reaching out! I recommend checking out the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR for your travel trailer. Hitches like this are universal fits so you just need to make sure the frame of your trailer is in the…

view full answer...

Answer 2

You will need to measure the distance between the side stanchions on your 2017 Keystone Carbon 357 to determine fit. The Curt Adjustable Trailer Hitch Receiver, #C13701 is for frames that are 18" to 51" in width. This is designed to work on…

view full answer...

Answer 3

I attached a picture of the side brackets of the Curt hitch part #C13701 for you to check out. I am not totally sure what dimension you are looking for but if you don't see what you need in the attached pictures let me know and I'll track it…

view full answer...

Answer 4

From the top of the mounting brackets to the top of the receiver tube on the Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2" #C13701 you were looking at is 4-3/8" as shown in the included…

view full answer...

Answer 5

Yes, if you plan on bolting the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR on then you would need to drill holes in the adjustable arms in order to set them to the correct length. There aren't any predrilled so that this one…

view full answer...

Answer 6

Based on our pictures the Curt adjustable RV hitch part #C13701 would not fit as-is. You'd have to relocate the stabilizers closer to the front of the RV.

view full answer...

Answer 7

I went out to our warehouse for you and took some measurements on the Curt Adjustable Trailer Hitch Receiver part #C13701. The distance from the outer ends of the crossbar is 51" long. The mounting brackets have a bolt hole to bolt hole…

view full answer...

Answer 8

I checked with Curt and was able to find a couple of diagrams of the mounting bracket and the receiver portion for the Adjustable Width Trailer Hitch Receiver item #C13702. I have attached them below. The width is adjustable between 22" and…

view full answer...

Answer 9

From the top of the mounting brackets to the top of the crosstube on the Curt Adjustable Width Trailer Hitch Receiver for RVs #C13702 measures about 2" and then from the crosstube to the end of the receiver measures about 6". I have…

view full answer...

Answer 10

The distance from the two bolt holes on each side bracket for the Curt Adjustable Width Trailer Hitch Receiver #C13702 is right at 8-5/8" (center to center). I have also attached a diagram to assist. This adjustable hitch will fit frame widths…

view full answer...

Answer 11

It's tough to tell from your picture which part of the frame I'm looking at, so if you can provide me with some more information on if that is a picture of the rear of the bus and those points on the frame are where you're mounting, I can…

view full answer...

Answer 12

I reached out to the manufacturer of Hidden Hitch which has been discontinued and replaced with Draw-Tite in most instances. The model of hitch you have has been discontinued but I was able to get the specs for you from the manufacturer. There is not…

view full answer...