Recommended Weight Distribution System for Aliner Classic Camping Trailer

Question

Question:

hello, would appreciate your advice: do i need a weight distribution hitch ? i recently purchased an Aliner Classic camping trailer 57 inches high when folded down, Wt 1515 lbs, GVWR 2100lb, dry hitch wt 190 lbs. I will be pulling it with 2015 Honda Odyssey, GVWR 6019 lbs, Towing capacity 3500 lbs, GAWR-F 2910 lbs, GAWR-R 3340 lbs. It has a 2 in, 3500 lb towing capacity ball mount hitch. Thank you

asked by: Bea H

1

Helpful Expert Reply:

For the weight capacity, you do not technically need a weight distribution system. However, due to the design of the trailer, I do recommend using a weight distribution system for the sway control features as the crosswinds or passing vehicles may create more sway than would be comfortable.

For your 2015 Honda Odyssey, I recommend the Strait-Line Weight Distribution System w Sway Control # RP66082 for your application because it will be a fit for your trailer tongue weight and any additional cargo weight behind the rear axle of your van and it will actively combat sway. The dual cam and spring bar system actively works to eliminate sway before it occurs by holding your trailer in line with your tow vehicle. It is designed to overcome those cams for turns and then automatically return to function upon completing the turn. I've attached a video to assist.

You will also need a hitch ball like # A-6 for a 2-5/16 inch diameter option or # A-90 for a 2 inch diameter ball.

Let me know if you have further questions.

expert reply by: Jason S

1

Patti

4/27/2024

I have a subaru ascent 5000 towing. Factory hitch. We pull a aliner Evolution 15 2350 3500 gvmr. Tongue i think is 200. Do you recommend a wDH? If yes why and which one. Aliner always say no to sway bars.

Reply

Answer 1

As far as function goes, the two controllers are actually pretty similar. The primary difference between the two is that the P3 uses what I would call a more user friendly display. Instead of an error code like what's displayed on the P2, the…

view full answer...

Answer 2

I did some research and found that your 2007 Mazda CX-9 is rated for 3,500 lbs towing capacity. We recommend weight distribution when the trailer weight is more than 50 percent of the weight of the vehicle doing the towing. Installing a weight…

view full answer...

Answer 3

According to my research, the Aliner Ranger Trailers did come standard with 10" electric brakes so you will need to install a 7-way trailer connector and a brake controller on your 2007 Toyota RAV4 in order to tow it. For this, you will need…

view full answer...

Answer 4

Typically, tow packages come with customized dash plug ports, a 4-way wiring harness, a 7-way wiring harness, a hitch receiver, and a transmission cooler. These are the standard tow package components that come with many models. With that being said,…

view full answer...

Answer 5

To add a 7-Way connector to your 2022 Toyota Sienna Hybrid you are going to need two separate wiring harnesses. I confirmed that both of these harnesses will fit the hybrid's and regular models of the 2022 Sienna. The first harness you will need…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yakima has an awning setup that will work with their round crossbars with the SlimShady roll out #Y36VR but there isn't a way to fit the Batwing Awnings to round bars.

view full answer...

Answer 8

It's very easy to install the Reese Pro Round Bar Weight Distribution part #RE94FR, it just takes a bit of time to go through the initial setup but then it will be much easier each time after. The hitch ball is already torqued down so all you…

view full answer...

Answer 9

With most weight distribution systems (including this Reese kit part #RE94FR), you can back up with the spring bars connected as long as you are backing up mostly straight, but if you are going to angle the trailer and tow vehicle sharply you need to…

view full answer...

Answer 10

I would be happy to help! Starting with the trailer brake controller you will need to first have a 7-way trailer connector installed on your 2017 Toyota Highlander XLE. If you do not you can add one using the Tekonsha OEM Replacement Vehicle Wiring…

view full answer...

Answer 11

It looks like the Aliner Scout has a dry weight of around 1350-lbs and a tongue weight of around 135-lbs when unloaded. Since you need a side-wind jack, I recommend using the etrailer.com Round, A-Frame Trailer Jack #TJA-5000S-B which will easily…

view full answer...

Answer 12

One easy solution is the Lippert Jack-It part #LC429756 which is a bike rack that attaches to the jack mounting flange and allows you to carry 2 bikes above the trailer jack. I attached a picture that shows it installed on a similar camper as well as…

view full answer...

Recommended Weight Distribution System for Aliner Classic Camping Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching