Expert Answers about Acura RDX
- Is Cutting the Bumper Required When Installing the Curt 12083 on a 2016 Acura RDX
- No! When installing the Curt # C12083 on your 2016 Acura RDX there is not any cutting or alteration of the bumper required. This is actually rated as one of the easier hitches to install and it will give you a 1-1/4" receiver for the back of your RDX. I've linked an installation video of this hitch for you to check out, as well.
view full answer... - Will Draw-Tite Class III Hitch # 75784 Install the Same on a 2011 Acura RDX as a 2010 RDX
- Yes, the Draw-Tite Class III Max-Frame Trailer Hitch, item # 75784, will install the same on a 2011 RDX as it does on a 2010 model.
The instructions, see link, indicate that you will not have to remove any body parts for installation of this hitch.
view full answer... - What is the Correct Trailer Wiring Harness for a 2010 Acura RDX
- I spoke with my contact at Curt and he stated that the Curt T-Connector Vehicle Wiring Harness, # 56008, has been tested on a 2010 Acura RDX so you can use it! I have linked a video showing an example installation for you.
view full answer... - Where is Fuse for Trailer Wiring Harness Used on 2008 Acura RDX Installed
- The Tekonsha # 118569 trailer wiring harness you'd looked at isn't a fit for a 2008 Acura RDX, it fits the 2013-2018 model.
For your 2008, you'd use either the Curt # 56008 or the Tekonsha # 118500. The 10A fuse included with the Tekonsha # 118500 or the Curt # 56008 installs in the inline fuse holder of the connector that plugs into the vehicle. The additional fuse included with the Tekonsha # 118500 isn't needed for the RDX installation, it's used if you're installing the harness on...
view full answer... - Installing Draw-Tite Class III Trailer Hitch on 2015 Acura RDX
- The Draw-Tite Class III Max Frame Receiver Hitch # 75784 referenced in your question is confirmed to fit your 2015 Acura RDX. We do not have any installers based in Maryland, however any local mechanic or shop with a good reputation should be able to handle the installation without issue. Because the hitch is custom-fit for your vehicle, it will use existing holes in the vehicle's frame for a no-drill installation. It has an estimated installation time of around 40 minutes. All of the necessary...
view full answer... - Rightline SUV Tent for 2010 Acura RDX
- Per the installation instructions, a roof rack is not necessary to attach the Rightline Gear SUV tent to your RDX.
Longer straps are included that can be used to pass over the top of the vehicle and ultimately attach to the windshield wiper arms. The tent also attaches to the edges of the rear wheel wells, and other straps attach to whatever points are available in the cargo area.
I have linked you to the installation instructions for the Rightline SUV Tent.
view full answer... - How Is 4-Pole Connector Routed to Hitch Once Installed on 2013 Acura RDX
- To use the trailer connector, you would simply pull the connector from the spare tire well and plug in your trailer. You then close the liftgate on the wire.
The rubber weatherstripping on the rear door is plenty thick enough that closing the door on the wiring will not damage it in any way as long as you keep the wiring away from the latch, which WILL damage it.
This seems like a very strange way of routing the cable, but keeping the connector stowed in the spare tire well when it is...
view full answer... - Factory Connection Point for Trailer Wiring Harness 118500 on a 2011 Acura RDX
- First, for a 2011 Acura RDX, you would need to use trailer wiring harness # 118500. The connection point is already present on the vehicle. It is behind a trim panel in the cargo area of your RDX. The small fuse will also need to be installed in a fuse panel. I have included a link to the installation instructions for you to view.
view full answer... - Will Draw Tite Hitch 36114 for 2020 Acura RDX Allow Handsfree Liftgate to Function
- We had a customer install the Draw Tite hitch part # 36114 on their 2020 Acura RDX and they said that to get the hands-free liftgate function to work they had to kick to the side of the hitch opening but they planned on moving the sensor to get even more functionality from it.
view full answer... - Installation Instructions for Tow Ready Trailer Wiring Harness # 118500 on a 2011 Acura RDX
- Installation of Tow Ready Wiring Harness, # 118500, is fairly straight forward. Below I have outlined the instructions for you.
First, open rear hatch. Temporarily remove all floor coverings, exposing the spare tire compartment. Remove the spare tire. Next, locate blue 6 pin tow plug near the foam cargo tray. It will be taped to the vehicle electrical harness with blue tape. Then, you will insert the T-Connector harness into the vehicle Tow-Plug harness and lock it into place. Locate a...
view full answer... - What Are the Torque Specs for the Draw-Tite Max-Frame Trailer Hitch Receiver # 75784
- In the attached installation instructions for the Draw-Tite Max-Frame Trailer Hitch Receiver # 75784 you can find the torque specs directly under step 4. Sometimes the manufacturers will slightly change some hardware to accommodate a wider range of vehicle so we always recommend checking with the current instructions (found on the link) just in case the torque setting has changed.
I have attached a sample installation video for you to check out.
view full answer... - Trailer Wiring Harness for a 2015 Acura RDX and Where to Stow the 4-Way Trailer Connector
- Trailer wiring harness # 118569 is the correct one for your 2015 Acura RDX. The wiring is designed so that the 4-Way end gets ran out of the hatch when used. The hatch can be closed on the wires as long as you keep it away from the latching mechanism. The vehicle weather stripping will protect it.
If you want to run it permanently on the outside of the vehicle then you will need to remove as much of the flooring and panels as you can in the cargo area. Look for a grommet that you can run...
view full answer... - Is Fuse Installation Required for Both Tow Ready Harnesses # 118500 and # 118569 in Acura RDX
- Yes, both of the Tow Ready trailer wiring harnesses you referenced, parts # 118500 and # 118569, require you to install the supplied fuse in the vehicle's fuse box located in the engine compartment.
Please note that these two harnesses are a fit for different model year ranges of the Acura RDX. The # 118569 fits 2013 and 2014 model years while the # 118500 fits 2007 through 2012 vehicles.
I have linked an installation video for your reference.
view full answer... - Curt Hitch and Identifying the 12 Volt Power Provision in a 2021 Acura RDX
- I have an explanation for your 12 volt power precision concern and a great hitch for your 2021 Acura RDX
In order to determine the correct trailer wiring harness for your 2021 Acura RDX - the option for +12-Volt Power Provision or without - you can check out the 8-pin connector on the driver's side interior trim panel. I have attached a photo to help you. I have also linked some installation instructions.
Once you see the 8-pin connector, check to see the number of red wires going INTO...
view full answer... - Options for Routing 4-Way on Curt T-Connector Vehicle Wiring # 56008 to Outside of 2015 Acura RDX
- My personal opinion would be to allow the connector portion of the Curt Custom Fit Vehicle Wiring, # 56008, to hang out of the hatch on your 2015 Acura RDX AWD when you need to use it. I myself would be a bit reluctant to drill any type of hole in my brand new Acura but this would be totally up to you. If you decide to drill a hole through the floor, double check to make sure that you will not hit anything on the underside of the vehicle. Be sure to seal up the hole once you are done to...
view full answer... - How Long Does it Take to Set Up a Weight Distribution System
- When we install weight distribution systems like the Pro Series Weight Distribution System # PS49901 that you referenced we set aside 4 hours to complete the job. We typically finish the job before the 4 hours is up, but for a first-time installer 4 hours would be about right.
I attached a link to an installation video for you to check out to the right.
If your driveway isn't level I would recommend finding a more level area.
view full answer... - Installing Draw-Tite Max-Frame Trailer Hitch Receiver # 75784 on 2017 Acura RDX
- The Draw-Tite Class III Max Frame Receiver Hitch # 75784 referenced in your question is confirmed to fit your 2017 Acura RDX. There is actually no fascia trimming or modification required for installation. On some models, it may be necessary to pull down a bit on the fascia to get additional clearance for the hitch crosstube, but this will not cause any distortion to the bumper. I have attached an image from the installation instructions to clarify this.
Otherwise this is a custom fit...
view full answer... - Is Spacer Block Needed When Installing Draw-Tite Trailer Hitch # 75784 on 2014 Acura RDX
- The Draw-Tite Max-Frame Trailer Hitch Receiver # 75784 referenced in your question is confirmed to fit your 2014 Acura RDX. For your 2014 model, the included spacer block is indeed needed. It will be taped into location on the top of the hitch at the rear most hole. I have attached an image to clarify this.
This Class III hitch will provide you with a 2 inch receiver opening and has a 4,000 pound towing weight capacity.
view full answer... - Will Trailer Hitch Get in Way of Kick Sensors for 2020 Acura RDX Advanced Model
- At this point in time (June 2020) the only trailer hitches that fit your 2020 Acura RDX come from Draw-Tite with their 1-1/4" # 36114 and 2" # 76268.
As far as the kick sensor goes, we have had a report from someone with a 2019 RDX with the Advanced model say that they were unable to get the kick sensors to pick up their foot with the hitch installed. When I looked into the possibility of a kick sensor relocation kit from Acura it looks like they say when they install a hitch the area...
view full answer... - How Difficult is the Curt C13154 Class III Hitch Installation on 2011 Acura RDX
- The Curt # C13154 Class III hitch install on a 2011 Acura RDX is pretty straightforward. One a difficulty scale of 1-10 with 1 being very simple and 10 being very difficult, we rated this install as a 4. We estimate a trained technician would take about 40 minutes to complete the install, or roughly double that for the typical do-it-yourselfer.
The only tools you'll need is a metric socket set and a torque wrench.
If you'll be using the hitch for towing purposes, you'll also need a trailer...
view full answer...
Go To Results