Expert Answers about Chrysler
- 2" Trailer Hitch Receiver for 2006 Chrysler Town and Country with Stow N Go Seats
- Yes, The Curt Trailer Hitch Receiver # 13389 will fit your 2006 Chrysler Town and Country LX with the stow n go seating. There is no drilling required for the installation of this hitch on your Chrysler.
You will also want the Hopkins Plug-In Simple Vehicle Wiring Harness # 42235 for connecting your trailer lights, if you plan on doing any towing. This can also come in handy if you are using a bike rack or similar carrier that may block the taillights on your Chrysler.
view full answer... - Will the Thule Motion XT Cargo Carrier fit on my OEM Crossbars On My 2020 Chrysler Pacifica?
- There is not. There are only two sets of tracks to attach the Thule Motion XT Rooftop Cargo Box # TH629906 to one set (of 2) crossbars.
The only stipulation Thule has for the Motion XT is that the crossbars it attaches too is at least 23-5/8" apart and no more than 36-7/8" apart.
If you were worried about rear hatch clearance, you'll just want to also make sure that there is at least 55" of clearance from the front of the crossbar to the line where the roof and the hatch meet.
view full answer... - Trailer Hitch for 2021 Chrysler Pacifica Hybrid
- Yes, the # e98903 that is displayed on etrailer.com will fit your 2021 Chrysler Pacifica; this is confirmed to fit both the hybrid and non-hybrid models.
view full answer... - Will Installing a Trailer Hitch Still Allow Hands Free Liftgate to Work on a 2019 Chrysler Pacifica
- A trailer hitch won't keep the hands free liftgate on your 2019 Chrysler Pacifica from working but it may be a little more difficult for the sensors to pick up the movement from your foot due to the extra material that is blocking it. If you check out the picture that I attached you can see the places that we have found work best with a trailer hitch installed if you use a forward and back kicking motion as opposed to swiping left to right.
If you haven't already decided on a trailer hitch...
view full answer... - Will Ultra-Fab Motor Home Trailer Hitch # UF35-946401 Fit a 2008 Chrysler Aspen
- The Ultra-Fab Motor Home 2-Inch Trailer Hitch, part # UF35-946401, is intended for installation on the rear of motor homes that have an exposed 4-inch bumper. Installation requires that the bumper be fully open in order to allow the U-bolts to attach securely.
This hitch is not suitable for use on your 2008 Chrysler Aspen. The bumper on your vehicle is designed to protect the passengers in the event of an impact. Even if you removed part of the bumper cover to expose the bumper itself,...
view full answer... - Adjustable Ball Mount Options For Bumper Clearance and 9 Of Rise
- I do have an options for you but the Flash Solid Steel Adjustable 2-Ball Mount part # FA49-00-5900 measures 3-3/4" from the hitch pin hole to upright portion of the ball mount so it will not clear the bumper of the Chrysler Town and Country. These measurements can be found in the video of the Flash Solid Adjustable ball mount that I have attached.
I recommend the Convert-A-Ball Adjustable Ball Mount for 2" Hitches part # TK5007 which provides 9" Rise to 10-1/4" Drop and can be used with...
view full answer... - Timbren Rear Spring System Compatibility With Aftermarket Shocks on 2010 Town and Country
- I spoke with my contact at Timbren about the compatibility of the two systems, and he said that as long as the Timbren Rear Suspension Enhancement System # TDVRRT and the shock absorbers don't occupy the same space they will work great together.
The Timbren system will replace the bump stop inside the coil spring on your 2010 Chrysler Town and Country. I have attached an installation video of the # TDVRRT system on a 2009 Dodge Grand Caravan for you to see the installation process. The...
view full answer... - Will the SportRack Vista XL Cargo Box Fit the Factory Roof Rack on a 2010 Chrysler Town and Country
- In order to determine if the SportRack Vista XL Cargo Box, # SR7018, will fit the factory crossbars on your 2010 Chrysler Town and Country, you will need to measure the width of the crossbars and the distance between the bars.
If the crossbars measure under 4 inches wide, the mounting hardware will fit. And, as long as the center to center distance between the two bars is 25-7/8", 27-7/8", or 29-7/8", the box will fit your factory rack.
view full answer... - Will a Thule Motion XT Fit on 2015 Chrysler Town and Country Factory Crossbars
- Yes. The Thule Motion XT # TH629706 will fit on the factory crossbars on your 2015 Chrysler Town and Country without any issues and provides you with 16 cu/ft of storage space. I noticed you also looked at the Motion XT Alpine # TH629506, which is also a 16 cu/ft box that will fit on your factory crossbars. It's a bit longer and not as tall though, so it might not be exactly the correct fit for your cargo.
I've linked some review videos of these parts for you to check out, as well.
view full answer... - Does the Thule Hull-A-Port TH848 Fit My 2017 Chrysler Pacifica?
- Yes, the Thule Hulla-A-Port XT TH848 Kayak Carrier will fit your 2017 Chrysler Pacifica as long as it has a crossbar system. The only crossbar system that will work on your 2017 Pacifica is the SeaSucker Monkey Bars # 298-SX6000B. As far as installation, the Monkey Bars involve the easiest installation out of any system we currently carry on etrailer. You simply press the pump on each vacuum cup several times and pull up tab to remove. In addition the Monkey Bars come with an impressive...
view full answer... - Trailer Hitch and Wiring for a 2008 Chrysler Sebring Convertible with Dual Exhaust
- Draw-Tite trailer hitch # 24871 will fit your 2008 Chrysler Sebring convertible with dual exhaust. It can be used to tow a rental trailer. The hitch has a 2,000 pound gross trailer weight capacity but check the vehicle owners manual to the Sebring's capacity and go by whichever is lower.
You will need the proper ball mount, part # 3594. To add a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring you can use # 118444 to add a 4-Way flat connector. I have...
view full answer... - Draw-Tite Trailer Hitch Recommendation for a 2000 Chrysler Town and Country
- The Class II Hitch that will fit your vehicle is the Draw-Tite Trailer Hitch for the 2000 Chrysler Town and Country, part # 36296. This is the Class II Hitch from Draw-Tite for your vehicle. There is a Class III hitch available for your 2000 Chrysler Town and Country, also.
I would recommend going with the Class III hitch from Draw-Tite for the 2000 Chrysler Town and Country, part # 75119, because it has a greater weight capacity and there are less limitations on what accessories you can...
view full answer... - Fit of Saris Bones Trunk Mounted 2 Bike Rack on 2013 Chrysler 200 Convertible
- According to Saris, their # SA805BL Bones two bike trunk mounted bike carrier isn't compatible with the convertible model.
Hollywood Racks offers several 2 bike models that will fit. I'd recommend their Express 3 bike model, part # HRE3. However, this will not fit if your 200 is equipped with the factory spoiler.
If you do have a spoiler, I recommend the Malone Hanger Trunk Bike Rack for 3 Bikes - Adjustable Arms # MPG2139, you can use it with 1, 2, or 3 bikes. This rack is confirmed...
view full answer... - Fit of Hitch Covers and Ball Covers on 2-Inch Hitch on 2007 Chrysler Aspen
- If you want a cover for your actual hitch ball itself you can use # 42250 or one of the others shown on the included link.
In the case of your 2007 Chrysler Aspen the only size of hitch receiver that is offered is the 2-inch Class III type; please see the linked page. Hitch BALLS can be a 1-7/8-inch diameter (or 2-inch or 2-5/16-inch) but a hitch receiver itself, which is mounted to a vehicle frame, will generally be either 1-1/4-inch, 2-inch or 2-1/2-inches square.
In your 2-inch hitch...
view full answer... - Can the Yakima 60" HD Tracks for Roof Racks Be Used on a 2018 Chrysler Pacifica with a Naked Roof
- The Yakima 60" HD Tracks for Roof Racks # Y74MR was designed to be used on truck bed rails or truck bed caps. It was not intended for use on the roof of a vehicle. That being said, it does not mean that you cannot do it. It simply means that there is no guide as to which vehicles it would be a good fitment for.
I did take a look and did not see another roof rack option, so installing tracks would be a good option. But, you will need to measure your roof to ensure you have the space. The...
view full answer... - Will the Thule OutWay 2 Bike Trunk Mount Bike Rack Fit a 2004 Chrysler Sebring Sedan
- Yes, Thule does list the OutWay 2, # TH45JV, as a fit for your 2004 Chrysler Sebring sedan. I had a chance to use the OutWay series of racks and they are probably the easiest racks to put on/take off. What makes it so easy is because it uses retractable cables instead of straps to secure to the vehicle.
If you will be carrying women's, children's, or alternative frame bikes, I recommend using the bike adapter bar, # TH982XT, in order to hold the bikes more level. I have included links...
view full answer... - Will a SportRack Vista XL Cargo Box Fit on a 2011 Chrysler Town and Country
- As long as the diameter of the crossbars on your 2011 Chrysler Town and Country are less than 4 inches and are 25-7/8", 27-7/8", or 29-7/8" apart on center this SportRack Vista XL Cargo Box # SR7018 would work for you.
view full answer... - Do Swagman Upright Roof Bike Carrier S64720 & SportRack Kayak Carrier SR5511 Fit Rhino-Rack Bars
- The Rhino-Rack square bar 2500-Series roof rack made of parts # RRVA126B-2, # RRRLKVA, and # DK199 is a confirmed fit on your 2010 Chrysler Sebring 4-door. Both the Swagman Upright Roof Bike Carrier # S64720 and the SportRack J-Style Kayak Carrier # SR5511 are fully compatible with this roof rack.
Installation videos for all three products are linked for your reference.
view full answer... - Will Yakima EasyTop Universal Fit Roof Rack part # Y07418 Leak Water
- We had one customer come back and tell us that in a heavy rain the fabric straps of the Yakima EasyTop Universal Fit Roof Rack part # Y07418 did allow some water to drip into the interior of the vehicle. Unfortunately there's no way to avoid that unless you'd be willing to install a roof rack like the Rhino Rack part numbers # RRVA137B-2, # RRRLKVA, and # DK318 which is a much more secure rack for your 2013 Chrysler 300 and will not leak.
view full answer... - Correct Trailer Hitch for a 2013 Chrysler 300S
- The trailer hitch options for 2013 Chrysler 300 are all compatible with the S models. I recommend going with the larger 2" opening due to the higher capacity and abundance of hitched mounted accessories for this size. The Curt Trailer Hitch Receiver part # C13093 offers a bolt-on fit with no drilling required.
view full answer...
Go To Results