The center mounting hole of the Trailer Reflector, Round 2-3/16" Diameter, Screw Mount # RE35AB you were looking at measures 3/16". The screw to mount the reflector to your trailer is not included but you can find a screw at your local hardware store. view full answer...
When we installed the Curt hitch # C11402 on a similar 2018 Hyundai Sonata to your 2019 model we found that from the top of the hitch down to the ground measured 10-1/2 inches. Since Class 3 hitches are only available for higher capacity vehicles that are much larger non are available. Also we do not have any multi-fit hitches that would be reasonable to try and fit on your vehicle either. view full answer...
I have a solution for you but the Curt Trailer Hitch item # C13900 will not fit your 2015 Tucson and even if it did it wouldn't increase your vehicles towing capacity. It looks like the 2015 Hyundai Tucson has a maximum towing capacity from 1,000 lbs to 3,500 lbs depending on the model. You can call a dealership and give them your VIN and they'll tell you yours.
To add a hitch to your Tucson, I recommend the Curt Trailer Hitch item # C13066. This hitch is custom fit and bolts to your Hyundai... view full answer...
The Curt Trailer Hitch Receiver part # C13152 is rated for up to 6,000 lbs. However, your 2017 Hyundai Santa Fe is only rated for 2,000 lbs unless you have the factory tow package then you are rated for up to 5,000 lbs. The lower of the two ratings (hitch/vehicle) will need to be the limit you abide by. Please also note if the trailer is over 1,653 lbs it will need to have brakes according to the owner's manual. I have attached some other parts you will need below.
Curt T-Connector Vehicle... view full answer...
Your friend will first to consult the vehicle owners manual of his 2012 Hyundai Santa Fe to see what the towing capacity is for his specific model. If the towing capacity of the vehicle and the trailer hitch used exceed the gross trailer weight then the Santa Fe would be able to tow the trailer.
The Curt trailer hitch # C13073 is rated for 350 pounds tongue weight and 3,500 pounds gross trailer weight. Given the average weight of a horse this probably means that only one horse could be... view full answer...
The distance from the center of the hitch pin hole of the Curt Ball Mount part # C45100 that you referenced to the weld gusset is 4-1/2 inches. I went out into our warehouse and pulled one to get this measurement. view full answer...
On the Curt Ball Mount # C45090 the distance from the center of the hitch pin hole to the near edge of the reinforcing gusset is 3-inches. From the hole center to the end of the shank the measure is 2-1/2-inches. I prepared a photo diagram for you to show these dimensions.
I also linked our main page for all 2-inch ball mounts. view full answer...
The Thule Camber 2 hitch-mount bike rack # TH9058 is compatible with Class I, Class II and even larger 2-inch Class III hitches. This rack would be a great option isince you already have a hitch on your 2005 Hyundai Accent GT. Currently, (October 2023), we do not offer a hitch to fit your Accent.
The Camber 2 weighs in at around 28-lbs so even with this weight added to your bike's own weight you will be well within the 200-lb tongue weight limit for the hitch. view full answer...
Since your kayaks are on the heavier side you'd need a carrier with a higher weight capacity like the Rhino Rack # S510 which has a 99 lb weight capacity. This would attach to the Whispbar roof rack you have as well. view full answer...
With the Draw-Tite Sportframe Trailer Hitch Receiver # 24884 you will have approximately 8" of clearance to the bottom of the hitch on your 2012 Hyundai Accent. Please be aware that this is an estimate as if your particular vehicle may have larger or smaller diameter tires. Also the amount of weight that is being carried inside your Accent will change your hitch height as well as aged suspensions may sag a bit due to age.
I recommend installing the Hopkins Tail Light Converter Kit # HM48925... view full answer...
The Westin E-Series tube steps, # 23-3425, have a weight capacity of 300 pounds. Though the bars themselves may be capable of more weight, the mounting hardware and locations on the vehicle limit the capacity. view full answer...
To use the etrailer Motorcycle Carrier, part # e98873, you'll need to equip your 2017 Honda Tucson with 2" Trailer Hitch Receiver.
I recommend the Draw-Tite Class III Max Frame Receiver Hitch, part # 75836. This easily installs without drilling and will provide the right type of hitch to carry your dirt bike. However, my research shows that a 2017 Tucson with a 2.0 engine would have a tongue weight of only 150 pound and with a 2.4 liter engine it would have a tongue weight of 200 pounds.
The... view full answer...
Lunette rings like the Curt SecureLatch Lunette Ring - Adjustable Channel Mount - 3" Diameter - 40,000 lbs # CU99FR do not have tongue or vertical weight limits.
These types of rings are designed for heavy duty situations and loads and are not rated the same way you would a standard ball mount or trailer hitch.
You are only limited to the capacity of the tow vehicle and the trailer you are attaching the lunette to. So make sure you double check the load ranges of your owners manual and... view full answer...
The Curt Class I hitch part # C11424 that you referenced does fit your 2018 Hyundai Elantra Sedan and has a towing capacity of 2,000 lbs trailer weight. I looked up the towing capacity of your vehicle and it appears to have a 750 lb trailer towing weight capacity so you'd be limited to that as your overall towing capacity.
Then for trailer wiring you'd want the part # 118692 which is a custom fit option with a very reliable converter box as well.
Then for a ball mount you'd want the... view full answer...
I verified with Kuat that the Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount - Gray # SH12G has shipping box dimensions of 44” x 14” x 11”. Also, keep in mind the shipping weight is about 44lbs. I attached a short demonstration video for you regarding this bike rack. view full answer...
To add some crossbars to your 2023 Hyundai Palisade, you will want the roof rack by Yakima which includes the following parts:
Yakima JetStream Crossbars - Aluminum - Black - 50" Long - Qty 2 item # Y00425
SightLine Towers for Yakima Crossbars - Flush Side Rails - Qty 4 item # Y64AR
SightClip Fit Kit for Yakima SightLine and RidgeLine Roof Rack Towers item # Y79AR
This aero bar roof rack system has a 165 lbs capacity. I recommend adding the Yakima Same Key System item # Y07204 to prevent... view full answer...
If your boat trailer came equipped with hydraulic drum brakes on both axles, it is best to keep both sets in working order, but if this is the route you prefer you'll want to put the new brakes on the rear axle where most of the boat's weight will be concentrated.
I linked our main page for hydraulic drum brakes. You can use the filters on the page to select your overall axle capacity (both of your current axles' capacities added together) to see if we have brakes of the appropriate rating,... view full answer...
In order to determine the departure angle with the Draw-Tite Sportframe Trailer Hitch Receiver # 24757 installed on your 2008 Hyundai Sonata more information would be required. Although we know the distance from the top of the inside of the receiver to the ground, which is 10-1/2", the distance from the "impact point" to where the tire contacts the ground is unknown.
If you're truly going into a 45 degree angle then this would require a distance of approximately 11.3" from the point where... view full answer...
Go To Results