The Replacement Hitch Tite Anti-Rattle Hitch Pin for Saris Bike Racks part # SA3021 uses a 1/2"-13 bolt. I am not sure what you mean by pin diameter as the above is a bolt, not a pin but if this was not the information you were looking for please just let me know. view full answer...
The B&W Companion 5th Wheel Trailer Hitch w/ Slider # BWRVK3400-5W weighs about 282 lbs while the Custom Underbed Installation Kit # BWGNRK1116-5W for your 2019 Ford F-250 Super Duty weighs in at about 143 lbs. I reached out to my contact at B&W who confirmed this so you will be adding about 425 lbs to your pickup.
Since you don't have the factory towing system installed I recommend adding the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness with 7-Pole Plug # 41157 as well.... view full answer...
You are correct that a level trailer will be less likely to sway and keeping your hitched trailer level will enable a weight distribution (WD) system to function at its best. It is perfectly okay for a hitch ball to be an inch or so higher than the coupler on the level trailer since a little bit of normal squat will even things out but if your trailer is tipped up at the tongue when it is hitched to your F-150 you'll want to select a different shank for your WD hitch that will allow the... view full answer...
I checked with B&W for you and the B&W Companion 5th Wheel Trailer Hitch # BWRVK3500-5W is 14-1/2" from the center of the hitch post to the front (cab-side) of the hitch when in the first position. To install this hitch in your 2012 Ford F-250 or F-350 Super Duty you will need the Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches # BWGNRK1111-5W.
This is a great choice as the Companion is considered by many to be the leading fifth wheel hitch in the industry.... view full answer...
The Karrier ST205/75R14 Radial Trailer Tire with 14" Galvanized Wheel - 5 on 4-1/2 - Load Range C # AM32156 does have a tire rated at 1,925 lbs at 60 psi. It is tire # AM10234 which I've linked for you to check out. The wheel is a lesser rated capacity of 1,870 lbs as you stated and is the Steel Spoke Trailer Wheel - 14" x 6" Rim - 5 on 4-1/2 - Galvanized Finish # AM20354.
We don't make the combinations, the manufacturer does that part, but this combination will absolutely have the... view full answer...
The Fastway e2 Weight Distribution Item # FA94-00-1033 only comes with one set of bars. If your bars say 800lbs then I would go by the bars. If you plan on carrying more than the 800lbs on your 2017 F-150 you can always add higher rated spring bars like Item # FA94-02-1099 which have a 1000lb tongue capacity. Keep in mind the F-150 max towing capacity is under 12000lbs so you want to make sure you do not exceed the truck maximum towing capacity and payload. view full answer...
The CargoSmart Standard Track Bungee Straps part # 3481712 are only designed to secure small items inside a trailer therefore, they don't have the max break strength or working load limit (WILL) rating that you are after as the manufacturer simply does not test for this. However, I can tell you that anytime you are using a set of e-tracks, the weight capacity of the tie-down will be limited by how the track itself is mounted. If you needed to secure heavier items on the e-tracks you would... view full answer...
The overall width of the Replacement Conveyor Pintle Chain Repair Link # 3371401102RL is 1.953 inches and the distance between pins is 2.250 inches. These is standard dimensions for the Repair Link 667X. view full answer...
If you are talking about the small opening on the outside and inside of the Orifice Connector # T1209800 then those measure 0.0010" and 0.0865" respectfully. I went out to the warehouse and measured them with the digital caliper.
Please note that this has 1/8" pipe thread male end to 3/16" brake line fittings and is designed for use with Titan Models 6, 10 and 20 as well as Dico Models 10, 20, and 60 actuators and new style Dico master cylinder. view full answer...
The measurement on the Westin E-Series Round Nerf Bars # 23-2310 is 6' from bolt-center to bolt-center. Nerf bars are designed to be vehicle-specific, so these actually only fit a Dodge Ram Pickup and won't fit your 2000 Ford F-250. For a set of nerf bars that are confirmed to fit your vehicle, you need the cab size of your vehicle. For example, if you have a regular cab, I recommend the Westin E-Series # 23-1320. These provide the same look and function as the boards you were looking at,... view full answer...
Curt ball mount # C45042 measures 4 inches from the top of the shank to the top of the ball mount platform. I have linked a video review of this ball mount for you. view full answer...
The B and W Companion Slider for Ford fifth wheel rail kits part # BWRVK3370 sits 8-11/32 inches forward of the front puck it installs into. So if you measure 8-11/32 inches in front of the forward puck you'd be able to tell if you have clearance for it to fit with your tool box. view full answer...
The Lippert Components Anti-Billowing Kit for Solera Slide Topper Awnings - Black # LC78FR is designed to fit right over the slide awning roller as pictured. The inside diameter of the arm is 2.545 inches according to my tech contact at Lippert. view full answer...
My contact at K-Source advised that when folded inward their towing mirror set # KS61203-04F will still extend out from the vehicle mounting surface 4-inches. This set of electric towing mirrors is a confirmed fit on your 2014 Ford Van with non-heated powered mirrors. view full answer...
The rubber springs on the Timbren Rear Suspension Enhancement System, # TFR250SDG, measure 4-1/2 inches tall and this system has been confirmed to fit your 2011 Ford F-250 Super Duty.
I have included the installation video for you. view full answer...
I spoke to my contact at Tekonsha and he informed me that the P3 hasn't had any major overhauls since it's development. All versions of it have the same 3 axis accelerometer.
You may be thinking of the P2 # 90885 that did get updated so that it's mounting range was increased.
Your P3 has the full mounting range that they all have. view full answer...
When you use an over under kit like the part # K71-385-00 that you referenced you will gain the diameter of your axle, the thickness of your spring seat, and the thickness of your leaf springs as a lift.
Also what you should consider is that when determining how much fender clearance will be left after going to a taller wheel/tire. Only half of the added diameter will be taken up in the fender well. So if you go with a 2 inch taller tire you would only lose 1 inch of fender/tire clearance. view full answer...
The majority of this Draw-Tite Max-Frame Trailer Hitch Receiver # 75691 will be hidden behind the rear bumper of your 2011 F-150. It will have the same basic appearance that the factory hitch for this vehicle would have. The hitch opening will be visible, but most of the rest of the hitch will be hidden. Installation instructions are attached.
You may be interested in the following products to complete your towing setup:
etrailer Ball Mounts # EBMK4
Draw-Tite Wiring # 18252 (installation... view full answer...