As far as what position they occupy in the bulb, I couldn't say. Dual filament bulbs like the # DI79VR have two different filaments. One filament is of a different resistance value, and thus makes a brighter light. but the brake and turn signal filament would be the brighter of the two.
From what you describe, it certainly sounds as if you have the brake/turn signal and running lamp wire reversed. view full answer...
I did a little research on your Lindy II RV and it was manufactured by Skyline. There are a lot of different motorhomes that were built on the cut-away van chassis, so the pictures you sent were extremely helpful. With the RV coming out that far from the rear axle, a hitch for the regular van won't work. We do however have universal-fit weld on hitches that you can have installed to allow you to pull your boat trailer.
Depending on the drop you need from your frame to get under the... view full answer...
The bolt holes will line up. The fact that the 1988 Chevy Van was converted to a bus doesn't since it is still on a G30 chassis/frame. The issue that you have to be concerned about is how the body of the bus will affect the fit of a trailer hitch.
The issue is that the hitches available were designed for the stock vans. The bus body likely hangs a little lower and further back from the rear axle than the stock van body which will cause fit issues. This is the case the vast majority of... view full answer...
I went out to the warehouse and pulled a Replacement handle, # DL22674, to measure it for you. Where the handle bolts to the jack, the inside width is 1/2 inch. I have included a link to a video review featuring this handle for you. view full answer...
We have the Draw Tite hitch part # 41121 as a confirmed fit for your 1983 Lazy Daze Class C motorhome that is built on a G30 frame. We had a customer come back and leave a review for this hitch where they told us it fit really well on their G30. view full answer...
On Curt trailer hitch # C13702 from the face of the receiver to the center of the nearest set of bolt holes is approximately 4.25 inches. From the top of the brackets where they attach to the bottom of the frame to the top of the receiver tube is 2 inches. The same measurements can be found on the Draw-Tite hitch # 5350. view full answer...
The Furrion Chill Replacement RV Air Conditioner for Furrion Setup - 15,000 Btu # FR58PR will only fit roofs 3-1/2" to 6" thick so you will need to increase the thickness of your roof at least another 1-1/2".
If you don't already have a a Furrion setup in your trailer you'll want the # FR92PR which will also come with the air distribution box (which also has controls on it) or the # FR55PV which will come with the air distribution box and a wall thermostat. view full answer...
The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Lithium Charger # PD4045LIKA you reference has been discontinued, and is no longer available from the manufacturer. This product has been replaced with the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger # PD4045KA.
This new version has a toggleable switch to allow you to switch to lithium, so they've discontinued the lithium only version. view full answer...
For your 2012 Jeep Liberty, the Mopar roof rack was made by Thule and the key you need is not a 900 but rather a 006. You will want the Replacement Key for Thule and Sportrack Racks and Carriers # THKEYN006. view full answer...
There are not specific installation instructions when it comes to installing transmission coolers, but there are basic guidelines for installing one that are pretty universal.
The first step for installing this Derale Series 8000 Plate-Fin Transmission Cooler Kit, part # D13504, on your 1993 Chevy G-30 van with A/C is finding the best location for mounting the cooler.
If you mount the cooler in front of the radiator, you will get the most cooling efficiency from the cooler, whereas it... view full answer...
I took a look a the instructions for the Firestone Coil-Rite Air Helper Springs - Front Axle # F4100 and the only warning listed has to do with the coil spring. The air bags should not be inflated when they are unrestricted, they must be restricted by the coil spring. So as long as they will still be restricted by the coil spring there shouldn't be any issues, but you could deflate them if you want.
I have attached the written instructions for your reference. view full answer...
Curt front-mount hitch # C31016 is specified to fit certain GMC and Chevrolet vans and RV cutaways but not until the 1996 model year. I show no custom-fit front-mount hitches for this vehicle, only rear-mount hitches from Draw-Tite, # 75121 and # 41121 for vans without the step bumper.
I also checked directly with Curt and Draw-Tite and neither shows any front hitch fits. My Curt contact suggested a universal-fit RV-type hitch as a possible work-around.
We do offer several adjustable/universal-fit... view full answer...
The Curt Trailer Hitch Receiver part # C13016 is only a confirmed fit for a 1978 - 1996 Chevrolet Van which excludes conversion models. The reason for this is because the conversion van models do not have the mounting hole for the bumper which is the front facing hole on the Curt Trailer Hitch Receiver closest to the receiver tube opening. I spoke with Curt and all they were willing to release is the distance between the two holes left to right which is 40.873".
I recommend the Adjustable... view full answer...
I spoke with my contact at DeeZee and the length of the driver side step of the # DZ3005 is 36 inches and the passenger side is 87 inches. Overall width is 7 inches.
At first I was confused by the large length difference between the two but then remembered this fits a Ram Promaster which on the driver side only has the driver door and the passenger side has the cargo area door too. view full answer...
Draw-Tite trailer hitch # 41121 fits the full size 1995 Chevy vans like yours and does not require drilling or trimming for installation. It does not fit models with a step bumper and based on your picture you do not have a step bumper so that is not a problem either. I have included a link to the instructions for you.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4... view full answer...
The first step I would take is to make sure that the 7-way trailer connector on your RV has power on the battery charge pin (see diagram). You can test for power using a circuit tester like part # PTW2993. The Tekonsha Prodigy RF, # TK94FR, requires 12-volt power from the tow vehicle to function properly. If your trailer connector does not have a constant 12 volts at the battery charge pin, then the main unit is not receiving power which would explain the nc code on the handheld unit.
Also,... view full answer...
The fan of the MaxxAir MaxxFan Trailer Roof Vent w/ 12V Fan - w/ Rain Cover # MA00-06200K draws 5 amps. In theory a 750 amp battery would power this for 150 hours. view full answer...
According to the research I did a G30 Chevy van is basically just a full sized van, so for your 1991 Chevy G30 van you would want the Draw Tite Hitch part # 41121 that you referenced as it has been confirmed to fit.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with... view full answer...
The air line that comes with the # AL88105 SHOULD be long enough for your application as it is 16 feet long and the replacement is # AL20086. The air line wouldn't need to run to the engine bay as it normally runs to cab. But we do have a 30 foot hose with the part # F9153 which will work great.
Or you could go with a remote compressor like the part # AL25980EZ which wouldn't require running line up to the cab since a gauge wouldn't need to be added there. view full answer...
The Curt hitch part # C13016 would fit your 1991 Chevy G30 conversion van/mini motorhome and would fit easily so this would be a great option. view full answer...
Go To Results