Currently the only receiver available for your 2006 Buick Lucerne is a class 2 like the Curt Trailer Hitch Receiver # C12044. This receiver is rated for up to 350lbs of tongue weight and towing up to 3,500lbs of trailer weight. Be sure not to exceed any manufacturer towing specs for your Lucerne. If you have a 2" accessory you are wanting to use the Trailer Hitch Receiver Adapter # HTAD will allow you to carry a 2" accessory with the 1-1/4" receiver.
The Vehicle Wiring Harness # 56047... view full answer...
The Replacement Hardware Kit # RHK will include all the original hardware components for your Curt Trailer Hitch # C12044, including the L-brackets that you mentioned. The picture on the product page for this kit is just a generic image and doesn't represent what you will actually receive.
Just make sure to type the model number of your hitch (C12044) in the text box provided and select "Curt" from the manufacturer drop-down menu when ordering and we will sent out the correct hardware. view full answer...
The Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # HM11141395 is a confirmed fit for a Buick Lucerne from 2006 - 2011, therefore it does indeed fit your 2010. If you need any other parts to start towing with your 2010 Buick Lucerne such as a trailer hitch and ball mount/hitch ball, check out the list I have created for you below.
Curt Trailer Hitch Receiver part # C12022
Curt Drawbar for 1-1/4" Hitches part # C45520
Curt Hitch Pin and Clip part... view full answer...
I went and grabbed a Americana Baby Moon Trailer Wheel Center Cap # AM90086 from our warehouse to measure the depth and I found that the lip of the cover is right at 1/2 inch deep and the overall depth of the entire cover is 2-3/4 inches. view full answer...
I looked up the specs on the oil filter of your 2007 Buick Lucerne with a 3.8 liter V6 and the thread size is 18 mm x 1.5 so for the correct sandwich adapter you'd need the part # D25773. view full answer...
I do have a hitch option for your 2008 Buick Lucerne to transport a 500lb electric wheelchair, but it will require a trailer as your vehicle is not rated for the amount tongue weight that a carrier would have.
What you'll need is the following parts:
Hitch # C12044
Ball Mount # C45520
Hitch Ball # C40001
Hitch Pin and Clip # F-4
Wiring Harness # 56047
and a small trailer like the Detail K2 # K2MMT4X6
To be able to use an actual carrier like # FHG69ZR you'd need to have a full size SUV... view full answer...
The tan WeatherTech Front Auto Floor Mats that will fit your 2007 Buick Lucerne is part # WT453081. The WeatherTech floor mats, # WT452681, that you referenced are designed for the Buick Lacrosse and will not fit your vehicle.
We also carry the WeatherTech floor mats for the second row and cargo area as well. For the second row of seats you will want to look at part # WT453082 and for the rear cargo area part # WT40463. All of the floor mats that I referenced were designed to fit your vehicle. view full answer...
We do offer replacement bulbs in the 921 type including both incandescent bubs like # 30-90-021 as well as LED types that are brighter, more efficient, cooler in operation and longer-lasting. Colored bulbs are offered, such as the Putco wedge lights # P230921B360 in blue and # P230921R360 in red. view full answer...
For your 2008 Buick Lucerne, there are a couple of options you can consider. You can opt for a roof rack that would be versatile enough to handle a variety of carriers, or you can choose to use a cargo bag like part # RL100A20 that will actually sit on the roof of the vehicle. If you choose this option, I recommend a protection pad like part # RL100650. This would provide a barrier between your vehicle roof and the cargo bag and prevent scratches and abrasions.
If you decide on a cargo... view full answer...
According to the Kat's application guide if you have a transverse engine (which it looks like you do) then it will be located at the rear center location (center location of the side towards the driver's seat).
This is where you will install the Kat's Heaters Custom Engine Block Heater # KH11484 on your 2010 Buick Lucerne 3.9L. view full answer...
I spoke with our contact at Hopkins and he was able to tell me that the winter protection windshield cover # HM17511 is vinyl and sewn on the edges.
If you tend to leave the windshield cover on 24/7 is may deteriorate quicker over time but in general the product life should last quite a while. There isn't a specific life span for this product because there are so many variables that could affect it's life expectancy.
The information available on this product is limited. view full answer...
The Super and Special are trim and packages that the 2008 Buick Lucerne could come with. The CXL Special Edition will have a chrome grille and chrome clad 17 inch wheels and a badge on the trunk that indicates it is a Special model. The Super can be identified by a rear spoiler. If you have a Special or Super model, hitch # 36502 will fit.
For a different model 2008 Buick Lucerne the comparable Draw-Tite hitch is # 36309. I have included a link to the installation instructions and a video... view full answer...
For the 50 inch Inno Square Crossbars # INB127, what you'll want to use is the 40 inch wind fairing, which is the following part number:
- Inno Fairing for Roof Racks # INA261
Really smart choice going with a wind fairing for square crossbars, as it will really help cut down the wind noise, particularly at higher speeds. view full answer...
The replacement lens you need is available as part # A68RB. If you should need to replace an entire lamp assembly, that part would be # M68RB. view full answer...
According to the owner's manual for the 2006 Buick Lucerne it has a gross trailer weight capacity of 1,000 pounds maximum. It does not say that a transmission cooler is required. However, a transmission cooler is always a good idea, especially when towing, to keep the fluid cooler so the transmission is less likely to get damaged or wear out any faster than normal.
If you do decide to install a cooler the most popular option for models with the 4.6 liter V8 is # D13503. And we also recommend... view full answer...
In order to install the Curt Trailer Hitch Receiver part # C12044 on your 2006 Buick Lucerne you can use the Replacement Hardware Kit for Trailer Hitches part # RHK which has the same hardware that would have came with the above trailer hitch if purchased new. You will need to enter "C12044" into the hitch item number box and then select "Curt" from the manufacturer drop down. view full answer...
The best hitch to tow a small trailer with your 2009 Buick Lucerne is the Curt hitch part # C12044 as it has the best towing capacities. For a ball mount you'll then want the part # C45561, pin and clip part # F-4. view full answer...
In order to determine if your 2008 Buick Lucerne is a standard model CXL or a special edition, there are a couple of things you can do. If the driver seat is a power memory seat that remembers your settings and your tires are size 245/50R18, then you have a special edition. But the definitive way to determine the trim level of your Lucerne is to contact a local dealer and have them run the VIN number of the car and they will be able to tell you for sure which one you have.
The Curt Trailer... view full answer...
For your 2006 Buick Lucurne, there are a few trailer hitch options. All of the available hitches are custom fit and compatible with all models and wheel sizes of your vehicle. I recommend the Draw-Tite Class II # 36309 as its install time is a bit shorter than the others.
I have included an installation video on a 2006 Buick Lucerne for you to check out. view full answer...
It is possible to have brake flanges welded to an axle that does not have them, but this requires specialized jigs that ensure perfectly correct alignment. Any errors in the orientation of the brake flange can cause all sorts of issues with brake performance and brake wear. This is not a typical DIY kind of project.
Often when converting a no-brakes trailer to electric drum brakes it is far easier and often also more cost effective to simply replace the axle with one that includes brake... view full answer...
Go To Results