When using an Equal-i-zer Weight Distribution System w/ 4-Point Sway Control like # EQ37100ET, the Trailer Valet 5X # STC-V211 will not be able to be completely installed at the same time. However if you look at the attached dimensions of the Trailer Valet 5X system you may find that there is enough room behind the trunnion bars and bracket on the Equal-I-zer to keep the mount installed. If there is enough room for the mounting bracket to be installed and not come in contact with the... view full answer...
Most aftermarket tonneau covers and ladders racks are not compatible with each other when installed on the same vehicle. Most often this is due to them using the same mounting points, or similar mounting points that interfere with the installation or operation of the other item.
The tonneau cover and ladder rack combination that is known to work well consists of the BAK Revolver cover and the Thule TracRac SR Sliding ladder rack. These products can both install and function correctly on... view full answer...
For your 2018 Toyota 4Runner with the factory roof rack the only cargo box Thule recommends as a fit is their Sidekick # TH78GC. The distance between the roof and the bottom of the crossbars on your roof rack is so low that only the U-bolt style of attachment like what the Sidekick has will fit without interference. Yakima also does not recommend any of their boxes as fits either. view full answer...
We have towing components you can add to your 2018 Mazda 3 though I did take a look at the owner's manual and it stated that you should not tow a trailer with your vehicle so doing so would be at your own risk. If you do decide to tow you need to start with a trailer hitch, either the Draw-Tite # 24912 if your '18 Mazda 3 is a sedan or the Draw-Tite # 24914 if your Mazda is a hatchback; these are the best option because they will be the easiest to install.
The ball mount that Draw-Tite... view full answer...
Yes, the Reese Rail Adapter # RP30156 will allow you to install your Pro Series 15K standard 5th wheel hitch in the 2018 Ford F-250 that has the factory prep kit. The adapter drops right into the factory pucks and provides the equivalent of standard above-bed base rails. The hitch will install in the adapter in the same way that it does in standard rails. Do note that the adapter adds 2-3/4-inches to the height of the fifth wheel hitch it is used with. view full answer...
On your 2018 Ford F-250 with Factory 5th wheel prep package, the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle # AL57391 will fit. These springs will be adjustable between 5 psi and 100 psi for the load leveling support you desire. This system comes with the manual inflation valves to allow you the ability to adjust the air pressure using a compressor or pump.
You may also want to consider the Air Lift Load Controller Compressor System for Air Helper Springs- Heavy Duty -... view full answer...
You can use B&W Replacement Base # BWRVB3705 to convert your 20K or 25K Companion 5th wheel hitch from the Ford factory setup to the GM factory setup. The hitch head assembly will transfer right over to the new base and give you the same hitch as part # BWRVK3705 (25K) or # BWRVK3700 (20K) which are the GM versions.
If you also need a 7-way wiring kit for the truck bed you can use kit # C56000. view full answer...
The Dexter Brake Actuator part # 099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator. If you ever need to replace the fitting, it is part # T4750300.
I recommend Kodiak Brake Line for Single Axle trailers part # 18SI-BLKIT. The flexible line of the Kodiak kit has a thread size of 3/8"-24 and fits a 3/16" fitting like the one... view full answer...
If your 2018 Hyundai Santa Fe has flush mount rails with fixed mounting points I have an option for you to use the 47 inch bars but the Thule AeroBlade Edge Roof rack does not work with 47 inch bars. The bars that fit your roof with the Aeroblade Edge Roof rack setup are 35-1/4" inches long for the front crossbar part # TH7602 and 38-1/4" inches long for the rear crossbar part # TH7603. The kit comes with two different sized bars to fit the shape of your roof with just the fit kit part... view full answer...
I contacted Fan-tastic Vent and the Vent cover part # FVU1500WH works with your fan-tastic fan 6600. The fan lid does open to 11-1/2 inches tall and the cover is 10- 1/4 inches so the fan lid does not completely open with the cover attach but Fan-tastic does guarantee the fan will still work to it's fully intended speed. The fan lid not extending all of the way does not affect the motor or wear it down. The fan is still open enough to get the proper air flow. The Fan-tastic Vent cover is... view full answer...
The 2-5/16" Hitch Ball # 63840 will need a 1-7/8 inch wrench or socket like the Powerbuilt # ALL643216 to tighten the nut.
This hitch ball has a 20,000 lb capacity, is made of cold-forged steel with a chrome finish and comes with a lifetime warranty.
I've added a link to a video review of this hitch ball for you to check out. view full answer...
Yes, the Draw-Tite Trailer Hitch # 75685 will absolutely fit a 2015 Lexus GX 460; if you take a look at the accompanying photo you can see the hitch installed on a GX 460
This is a Class III, 2" trailer hitch that has a 5,000 lb towing capacity and 500 lb tongue weight capacity. It is a simple, bolt-on installation that does not require drilling into the frame of your Lexus to install; it is constructed from steel and comes with a lifetime warranty, which speaks to its durability.
I have... view full answer...
I reached out to a representative of Yakima who told me that for the 1-1/4 inch diameter round crossbars of a SeaSucker roof rack like the # 298-SX6000B, the Universal MightyMounts for Yakima Roof Mounted Accessories # Y03590 will fit around them.
They did caution that the MightyMounts not be the "best" fit and could roll a bit on your round bars but this is the only adapter that will allow you to use Yakima accessories on round bars that are 1-1/4 inches in diameter.
The MightyMounts... view full answer...
Curt has confirmed the fit of their Class I hitch # C11900 on the 2019 Chevy Camaro ZL1.
The Curt hitch bolts on using the included hardware pack and provides a 200-lb tongue weight rating. Installation instructions are linked for you.
If you will be using a compatible bike rack like the Kuat Transfer # KU74FR or a cargo carrier like the Curt # C18110 you'll want to use Curt Support Strap # 18050 to support and steady such items. You can use a compatible carrier up to the hitch's 200-lb... view full answer...
Your F-350 has a curb weight of 6,588 lbs from what I can find online. Most tow dollies like our Roadmaster # RM-2050-1 will not handle that capacity so even if you pulled your drive shaft that likely isn't an option. If you wanted to flat tow it, I can give you that complete setup, but you will also need to disconnect the drive shaft for that. A trailer may be a better option depending on your reason for towing.
If you want to flat tow it, I've attached an article to assist with the... view full answer...
There is a 2 inch hitch ball rated for 10,000 lbs that is compatible with the Curt Ball Mount # C45338. I recommend the 2" Hitch Ball # A-90 because it is rated for 10,000 lbs and has a shank that measures 1-1/4" diameter x 2-5/8 long so there will be minimal excess once the nut is tightened.
I have added a link to a video review of this hitch ball for you to check out as well. view full answer...
The correct Timbren Rear Suspension Enhancement System (SES) for your 2019 Ram 3500 pickup should be part # TDR3500CA because the other option, part # T94VR, is for Severe Service vehicles like tow trucks.
This kit has an 8,600 lb capacity and doesn't require any drilling for the installation, but please note that it will not fit if you have the factory Air Suspension system. Another thing to remember is that this will not increase the weight capacity of your pickup as it is designed to... view full answer...
Unfortunately there is not an offset ball option compatible with the Ford Factory hitch. The only gooseneck hitch with that offset option is the B&W Turnoverball. To give you additional clearance when towing, I recommend the B&W Extend-A-Goose Gooseneck Coupler - 2-5/16" Ball - 10" Offset - 24,000 lbs # BWTEXA4200.
If you are towing a 5th wheel with this gooseneck hitch, then the Ranch Hitch Universal 5th-Wheel-to-Gooseneck Coupler Adapter w/8" Offset for Short-Bed Trucks # AM3139.... view full answer...
I recommend going with the Stromberg Carlson 4000 Series Tailgate # VG-15-4000 for your 2019 Ford F-250 Super Duty because it features a lock for security and a louvered design that reduces wind drag. If you would like to keep prying eyes from peering into the bed of your pickup then you can install the Louver Insert Kit # 4000-V as well which fills in the gaps of the louvered design.
This tailgate has a glass-filled, black composite plastic frame that is lightweight but still sturdy.... view full answer...
I made a few calls to the RV manufacturer (Grand Design) and the chassis manufacturer (Lippert), what I was able to find out is that your 2019 Grand Design Reflections 303RLS uses a Lippert 1621 pin box therefore, I can confirm that the Sidewinder 5th Wheel King Pin with Rotating Turret part # RP34FR is correct for you. There won't be any compatibility issues with your Reese 16K 5th Wheel Trailer Hitch though you will need to use the Sidewinder Wedge Kit part # 30850 as well in order to... view full answer...
Go To Results