I agree, the bag for the NOCO Boost X Jump Starter # NOC88VR is a nice way to keep everything together but it definitely lacks in the protective department.
To keep your Boost X Jump Starter safer you'll want to pick up the EVA Protection Case # NOC24ZR which features a rubberized EVA exterior for protection.
Attached is a review video for you to check out. view full answer...
First you will need to install a 4-Way Vehicle Wiring Harness # CU94FR on your 2024 Kia Carnival if you do not already have one. Then you will connect the 7-Way Kit # ETBC7 which will plug into the 4-way flat connector. The kit also includes wiring for connecting the charge line and Tekonsha Prodigy P3 Trailer Brake Controller # 90195. view full answer...
You are still going to need the monitors that come with both the Furrion Vision S # FOS43TASF and the TireMinder i10 TPMS # TM89FR.
The pre-wire for your trailer just means the wiring for a Furrion camera system is already ran so you'd just have to plug the camera in and you'd be set.
Also, the K-Source Snap & Zap Custom Towing Mirrors # KS80930 will not interfere with the camera functionality on your mirrors because there is a cut out at the bottom of the mirrors for just this, and they... view full answer...
I wouldn't know what the OEM window knob looks like or what you need just based off of the YMM of your 5th wheel. With that said, we do carry a couple of different options for you to check out.
For a tri-lug window knob with a 9/16" shaft, you can use the Tri-Lug Window Knob # 37220165,
For a tri-lug window knob with a 13/16' shaft, you can use the Tri-Lug Window Knob # 37220185,
Or,
For a standard window knob with a 1" shaft, you can use the Window Knob # 37220335,
For a standard... view full answer...
For your Breakaway Kit Replacement 12 V Battery # HM20008 you can use the Replacement Box with Non-LED Lid for Engager Breakaway Kit # HM20120.
This box has internal measurements of 4 1/2" long, 4" wide, and 3 1/2" deep so it'll house your battery perfectly. view full answer...
You almost have everything, you're just going to need a fit kit # INK758. This kit will allow you to mount the Inno Feet for Square Crossbars # INSUT to your 2014 Mazda CX-5.
The # INSUT crossbars you mention have a dynamic weight capacity of 220 lbs, measures 50" long, 7/8" tall, and is 1 1/4" wide. view full answer...
The Atwood GC6AA-8 you're looking at has been discontinued for a couple years now so it's no longer available. I do have another suggestion if you're open to it.
In place of the Atwood, I recommend checking out the Furrion RV Tankless Water Heater # FR98SR. This water heater has similar dimensions as the Atwood measuring 12-5/8" wide x 12-5/8" tall x 19-1/4" deep, has a heating capacity of 13,000 to 60,000 Btu, and has an operating waterflow of 0.32 gallons per minute. view full answer...
My contact at Titan confirmed that you CAN change out just the inner portion of your Titan actuator ball coupler # T4747220 to convert it to a lunette ring type like # T4748000. The conversion kit you need is part # T4045600183, their Replacement Inner Slide Assembly with 3-Inch Lunette Ring for Titan Model 6 Actuator.
I have linked our main page for pintle hitch components. view full answer...
A 205/75-14 sized radial tire with load range C like # TR20514 has a weight capacity of 1,760 pounds so it will still be plenty for your boat and trailer. The outer diameter will drop less than a 1/4 inch so there will be very little change.
The only thing you'll want to make sure of is will the tire fit on your rim. A 205/75-14 will not fit on a 7 inch rim like a 215/75-14 will. So if you have a 7 inch rim it won't fit without getting new rims as well.
To measure the width of your... view full answer...
The base plate has mounting points for either a 6 or 4 way round connector to attach, but the connectors aren't included with the base plates.
I'd recommend cutting off the 4-pole flat provided by the Hopkins # HM56302 flat towing wiring harness and installing the 4 pole round connector provided with the 7-foot long Blue Ox 7-way to 4-pole round cord, part # BX88254.
I've linked you to some of our flat towing FAQ articles. view full answer...
For your 2017 Jeep Wrangler and Falcon 5250 tow bar you can use base plates # RM-521448-4. This is assuming you have the standard factory front bumper. If you have a different bumper let me know. For a Tow Defender screen use # RM-4700.
You will also need safety cables such as # RM-643 if you don't already have some. For lighting a popular option for Jeep owners is the 4-diode kit # RM-154. I have included a link to a video showing example installation for you.
You may also need a high/low... view full answer...
The Thule Snug Tite Hitch Lock, # THSTL2, uses a 12 mm hole diameter flat washer and lock washer when installing to the Thule bike rack.
These parts can be found at any hardware store if you need to replace just the washers.
If the pin needs replaced, you will need part # 853-5917. This is the threaded bolt pin that connects the hitch stinger to your vehicle's hitch. view full answer...
With a 3,500 pound axle you'll need brake flanges with a 4-bolt pattern like # 4-35. Your trailer may already have these and if so that's good. The brake flange needs to be welded to the end of the axle to support the brake assemblies. It will need to be welded perfectly straight for your brakes to function properly so the work should be performed by a certified trailer shop.
For brake assemblies, I recommend # AKEBRK-35-SA Left and Right Side Brake Kit. This kit will include 2-10 inch... view full answer...
If you already have the 4-pole wiring harness installed on your 2008 Toyota FJ, then all you will need is the 7-way install kit # ETBC7.
This kit will include the 7-way connecter, all the wiring, and hardware needed to install a brake controller to your vehicle.
If you do not have a brake controller yet, I recommend the Tekonsha Prodigy P2, # 90885. The P2 has 3 boost levels and will continuous do diagnostic check on you system to warn you of any issues the might occur when towing.
I... view full answer...
The Roadmaster base plate kit that fits your 2013 Ford C-Max is # 524432-1. This is the EZ2 base plate kit which has 1-1/4 inch tubes so you'll need # RM-212 receiver covers.
The # RM-210 covers are for base plates that measure 1-1/2 inches. view full answer...
For your 2014 Fleetwood Bounder Class A motorhome that is based on the Ford F-53 with V10 engine you can use the Roadmaster rear Anti-Sway bar # 1139-144. For a front anti-sway bar you can use # RM-1139-148. view full answer...
From the sounds of your situation the Ultra-Fab Skid Wheels # UF48-979014 seem to be a great solution. Sure beats damaging your driveway.
These are designed to attach to 2-1/2 inch square hitch tube on the motorhome. If you don't have this you can use # UF48-979012 that use brackets that weld to the RV. view full answer...
To use your Reese 5th Wheel Trailer Hitch # RP30047 on your new 2017 Ford F-250 with the factory rail kit, you will just need the Reese Elite Series Underbed Rail Adapter # RP30156. This will mount to the rails on your truck via the Power Puck system and is compatible with your Reese 5th-wheel trailer hitch. I have included a demonstration video of this product for you to review.
Since your F-250 has a shorter bed, you might also consider a sliding hitch like the Reese # RP30051. This... view full answer...
If all you need are the four lighting functions you can use # 118449 on your 2008 Toyota Highlander. Then connect it to your trailer's 7-way connector using the adapter # 30717.
To make it easier to mount the connector on your Highlander use the mounting bracket # 18138 along with the no drill mount # C57202. This way the 7-way adapter will have a clean look on the rear of the vehicle without having to drill into it.
If you don't already have a hitch receiver I suggest the Draw-Tite... view full answer...