The correct B and W Turnoverball Gooseneck Hitch for your 1998 Dodge Ram 1500 is the part # BWGNRK1394 and the measurements to use vary depending on your bed length. You'll want the hole centered from left to right but from the rear edge of the truck bed the hold would be 48-3/8 inches if you have a long bed or 44-3/8 inches if you have a short bed. I attached a picture that I took from the install instructions which shows this as well. view full answer...
I looked up the towing capacity of your 2004 Dodge Ram 3500 with the Cummins engine and it appears to have a 10,900 lb towing capacity which as long as you kept the trailer you are considering under that figure you'd be fine. This would mean keeping the trailer 1,100 lbs under it's max capacity which wouldn't be too difficult at all.
The best slider hitch solution we have would be the B and W Companion Slider part # BWRVK3400 as it's widely considered to be the best slider hitch around... view full answer...
The 7" Weld-On Bracket Kit part # 4907 which is designed to be used with the Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube part # 41990 or part # 41991 has two plates which are each 3/8" thick. There is also the 16" Weld-On Bracket Kit part # 4916 available which has side plates that are 3/8" thick as well. view full answer...
In regards to the Ranch Hitch Universal 5th-Wheel-to-Gooseneck Coupler Adapter part # AM3100, the bolt circuit diameter is about 8-5/8" on center whereas the overall diameter of the plate is about 9-3/4". I will say that most pin boxes are 12-12-1/2" wide so you should not have to worry about there not being enough space on the skid plate of your pin box.
I have attached a photo for you with the above dimensions. view full answer...
The DLB Series Brake Winch Ratcheting Replacement Handle # DL70347 does not have any type of rating on it. The weight rating will be on the winch itself. This handle is for any Dutton-Lainson winch in their DLB series. view full answer...
According to my contact at Reese the four spacer tubes included with their Super Titan 4000 Trailer Hitch # 38208 measure 15-inches in overall length and have a cross section that is 3-1/2 x 3-1/2-inches. The hole spacing is 11-inches on centers. Please refer to the linked diagram. view full answer...
From the top of the mounting flange of the Curt Trailer Hitch Receiver # C15704 to the top of the crosstube measures 6.65" as you can see in the included diagram.
I included a link to the written instructions of the # C15704 for you to take a look at. view full answer...
The Phoenix Faucets # PF231561 has the following measurements:
Spout 15 inches
Distance inside of spout 6-3/4 inches
Base to top of spout 9-1/4 inches
Nozzle to top of spout 4 inches
Handle 8 inches
Mount Flange 10 inches
Nozzle 3 inches
Shank 2-1/2 inches
Base 6 inches
I've attached a diagram that may be helpful too. view full answer...
If your 2014 Dodge Grand Caravan owner's manual indicates the vehicle's maximum tongue weight capacity is 360-lbs, then that is the maximum weight that can be placed on its hitch. If the combined weight of your scooter and the carrier you wish to use exceeds this weight capacity then you will need to use a small trailer instead of a hitch mount carrier to transport the scooter. At the 360 pounds that you mentioned, you would be fine.
Exceeding the vehicle's (or the hitch's) rated capacities... view full answer...
I took a trip to the warehouse to measure the spigot of the FloTool Conductive Fuel Filter Funnel # FTF8C and found the outside diameter is 3/4". The overall diameter of this funnel is 8-1/2" and it has a height of 10" with a flow rate of 5 gallons per minute. view full answer...
The Longview Original Custom Slide-On Towing Mirrors # CTM3100 have a mirror surface that measures 5-1/2 H x 4-1/2 W. The plastic housing from end to end measures 16-inches long. Both the mirrored glass part and the housing have gently curved shapes so exact dimensions will vary depending on where you measure but the dimensions above were taken at the center of the glass and housing.
These custom-fit mirrors are intended for various Dodge vehicles for model years 1994 through 1997. view full answer...
The distance from the front hole to the middle on the # 14001 is 5.2". From the middle to the rear hole is 4.04" and from the front hole to the rear hole is 9.2". The distance across for each set of mounting holes is 36". view full answer...
I grabbed a tape measure and went out to our warehouse to measure the Draw Tite hitch # 75210. From the center of the first hole to the edge of the receiver measured 9-3/4". From the second set of holes it is 12-1/2" to the edge of the receiver. I made a drawing for you which I have included below. view full answer...
The fact that your modified trailer has a third un-braked axle added in front of the two braked axles will not directly affect sway. Nor will the fact that it seems to balance pretty well on its own without a load.
Trailer sway, or the lack of it, is mostly a function of load distribution. If the loaded trailer is too light at the tongue (too heavy at the rear) the rear of the trailer will tend to swing like the pendulum on a grandfather clock. Tongue weight (TW) should always stay in... view full answer...
The Reese Universal Installation Kit (No Base Rails) - 10 Bolt, part # RP30439, is just the universal installation brackets. The Reese Universal Base Rails - 10 Bolt, part # RP58058, will be the base rails that are used with the Reese brackets # RP30439. If you need the universal brackets and the universal base rails together you would use the Reese Universal Base Rails and Installation Kit, part # RP30035.
To install the universal base rails on your 1995 Dodge Ram 3500 Dually the measurement... view full answer...
The female end, or the power inlet, with the weather resistant cover is 3.25 inches at its widest point. 4.5 inches tall and 3.75 inches long.
The male side of the plug is 4 inches long 3 inches wide and 3 inches tall.
Here are the two different color schemes with the same dimensions.
SmartPlug RV Power Inlet and Connector - 30 Amp - Gray # SM87FR.
SmartPlug RV Power Inlet and Connector - 30 Amp - White # SM77FR. view full answer...
I spoke to my contact at Westin and they informed me that the Westin HDX Front Bumper w/ Winch Mount part # 58-160625 is constructed of 7 gauge steel and weighs around 200 lbs. They were not able to provide the exact dimensions as it is a vehicle specific product and this is not a metric they record but I was able to get the dimensions of the shipping box if that helps which is 83" long x 20" wide x 30" tall.
If you have any other questions please just let me know. view full answer...
To determine the necessary clearance between the rear of the truck cab and the front of the trailer loft, use the formula below to ensure there will be enough space between your truck cab and trailer when executing a 90-degree turn.
(A + B) - C = Clearance
A = Distance from center of fifth wheel hitch jaw to truck cab
B = Length of kingpin extender
C = Width of trailer divided by 2 (to get half)
For example: If the distance from the center of the hitch to the cab is 36 inches, 36 + 22... view full answer...