The Stealth Hitches Hidden Rack Receiver # SH34VR is our part number which is the Stealth Hitches part number SHR31003. I do recommend installing the Towing Kit # 391CONVA7 with the receiver. This will give you a ball mount for towing as well as the wiring needed for a 4-way flat trailer connector. view full answer...
I checked with Inno, and there is not a set speed limit for the Inno Wedge 660 Rooftop Cargo Box # INBRM660WH.
That's not unusual though, as cargo box manufacturers each say to just drive the speed limit; they likely don't want to encourage high speeds.
The Wedge 660 # INBRM660WH will easily stay attached to your crossbars at highway speeds with its clamping system, or if you install it in your crossbars' channels with the Aero Crossbar T-Slot Mounting Hardware # INBRP12. view full answer...
A catalytic converter like part # MF99206HM is not intended to increase horsepower when installed.
The intent is to reduce the amount of contaminants released when the engine is running. Since the exhaust system is part of the overall tuning of the vehicle, if it were removed it would or could have a negative effect on the performance of the engine. The performance of the catalytic converter is monitored by the computer too, so any replacement converter must perform like the original.... view full answer...
You are good-to-go. The Progressive Dynamics Inteli-Power RV Converter and Battery Charger, # PD9160A that you currently have can be directly replaced with the # PD9160ALV model that is designed with lithium chemistry charging profiles. Each of these units are 12 VDC providing up to a 60-Amp charge for your battery bank. Providing your current set-up is properly matched in wiring to this 60-Amp rating, removing and replacing with the # PD9160ALV will not require you to replace charging... view full answer...
The tools that you need to install the Draw-Tite Max-Frame Trailer Hitch Receiver # 75600 on your 2018 BMW X5 are as follows.
-Heavy duty utility knife(for trimming the bumper fascia)
-Center punch
-5/32" rivet tool
-10mm socket
-18mm deep well socket
-Torque Wrench
New rivets are included with the receiver and you will reuse the factory flange nuts for mounting the bumper. view full answer...
You never mentioned the Thule ski rack you have, though I am going to assume it is the older Thule Flat Top, and we do have the needed parts so you can mount it in the T-slot of the crossbars on your 2014 BMW X3. What you need is the following:
- Replacement Square Head Bolt for Thule Flat Top Ski and Snowboard Carrier # 853208904
- Replacement Round Nut for Thule Carriers # 853-5439 view full answer...
We have an easy way to determine our recommended installers in your area. On each product page, there is text under the pictures and videos that states "Need help with installation? Find installers near me." Once you click on that link, you can input your area code to find a location convenient for you.
I went ahead and attached a photo that shows you where this link is located on each product page. view full answer...
Any time you install a weight bearing device on a vehicle that rests on a painted surface, there's the potential that the vehicle can be damaged. That's the honest answer.
That being said, there are things you can do to greatly reduce the possibility of that occurring.
• You'll want to make sure that the surfaces of the bike rack and the vehicle that touch each other are 100%
clean and free of dirt and grit. A good coat of high quality car wax applied to the surface of the vehicle... view full answer...
I can certainly help you out. The TW is the tongue weight. This is the weight of the trailer at the coupler that attaches to the ball mount on the trailer hitch. It should be 10 to 15 percent of the GTW or gross trailer weight. The gross trailer weight is the total weight of the trailer.
Weight distribution is a system that installs on the trailer frame and the trailer couples to a special shank on the trailer hitch. The spring bars that come with a weight distribution system take some... view full answer...
Although the Curt trailer wiring harness which we sell as # C56190KIT is connected directly to the battery to provide a reliable secure power connection for the trailer taillights, it won't pull any power from the battery unless the taillights are actually on.
If it would make you feel better, you could install a battery isolation solenoid like part # PK5231201 inline on the circuit ran to the battery so the feed shuts down when the ignition is off, but it's honestly not necessary.
The... view full answer...
There is absolutely no difference whatsoever between the Stealth Hitches products we sell and what would come directly from the Stealth Hitches factory.
The products are exactly the same, including the Stealth Hitches Hidden Trailer Hitch Receiver with Towing Kit # SH32VR which fits your 2020 BMW X7.
I have added a link to the installation instructions for you to check out as well of the Stealth Hitches Hidden Trailer Hitch Receiver with Towing Kit # SH32VR. view full answer...
I checked with the manufacturer and the Custer Red LED Safety Light with Heavy Duty Magnets # HF18R-HD will flash up to 32 hours or more with 4 AA batteries.
The quality of the batteries can affect performance. view full answer...
The MagnaFlow Performance Muffler, part # MF11365 is a Universal muffler and can be used for gas or diesel engines.
The inlet and outlet dimensions and length are what you need to make sure will fit for your application. The inlet and outlet for this muffler is 2-1/4 inches and the overall length is 17-inches. view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver, # 76288 is a confirmed fit for the 2020 BMW X5, excluding M Sport package. When properly installed it will match similarly to the factory hitch.
If you look below the product images, you will note "Need help with installation?" Please select the hyper link to locate installers in your area if you do not wish to do the install yourself.
This is a no-drill installation with an estimated install time of 2 hours. view full answer...
On our product page for the Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit # SH25VR there is a locate installers link just below the pictures and videos. This will allow you to search for installers near you with your zip code who will be able to install the receiver on your 2023 BMW X5. You can also search for installers on Stealth Hitches website if you do not find one close enough. view full answer...
The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit # SH25VR will not require any additional programming on your 2021 BMW X5. The wiring in this harness is passive so no programming required. You will be able to switch off the parking sensors by using the button on your console or by going through the menu options in the dash. For exact instructions see your owners manual.
Towing is generally preferred in sport mode as it firms the shifts and allows for the engine to go higher... view full answer...
The EcoHitch Hidden Trailer Hitch Receiver # 306-X7277 does rate a 10 out of 10 on our difficulty rating as it is a very in depth installation. It requires removal of the rear bumper cover and trimming of bumper cover, underbody panel and wire harness holder to properly install the receiver. There are several different tools such as a hack saw, coping saw, reciprocating saw, and a jig saw that would allow you to accomplish the cutting required. You will also need a basic set of hand tools... view full answer...
You will want to first check with your owners manual or with your dealership to find out what the roof weight capacity is for your 2008 BMW X3. With having a moon roof installed you may find that they recommend that nothing be placed on the roof surface or the moon roof of your vehicle.
There are a couple of options for roof top carriers for you. If you find that your roof can handle some weight with the moon roof I recommend the Rightline Sport 2 Rooftop Cargo Bag, part # RL100S20. this... view full answer...
The Secure-Fill RV Fresh Water Tank Filler w/ Shutoff part # A01-0035VP is not lead free as most brass fittings are not but it is below the minimum requirement needed to pass the Safe Drinking Water Act (SDWA) so it is safe to use for drinking water. view full answer...
The relays included in the Curt Relay Kit # C57000 that you referenced are all rated for 20 amps. I confirmed this with my contact at Curt.
I have attached a short video review that you can check out as well. view full answer...
Go To Results