T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
(243 reviews)
Price: $75.50
In Stock
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
Item # 118405
Retail:$87.02
Our Price: $75.50
You Save: 13%
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (243)
- Q & A (0)
- Photos
Tekonsha Custom Fit Vehicle Wiring - 118405
- Custom Fit
- 4 Flat
- Trailer Hitch Wiring
- Tekonsha
- Powered Converter
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Features:
- Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights
- Compatible with 5-pole, 6-pole and 7-pole adapters (sold separately)
- Connects quickly and easily
- Locate connection points in rear cargo area
- Plug in T-connector
- Run hot lead to car battery
- Includes ModuLite to ensure that your vehicle's wiring matches that of your trailer
- Powered module connects directly to battery to avoid overloading vehicle's electrical system
- Constructed of 16-gauge bonded wire
- Comes with dust cap for 4-way flat connector
Specs:
- Maximum amperage:
- Stop/turn lights: 2.1 amps per circuit
- Tail lights: 5.6 amps per circuit
- 1-Year limited warranty
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk or cargo space, behind the tail lights on both the driver's side and passenger's side. You will need to remove some interior trim or carpeting to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse.
Once installation is complete, the 4-way flat connector will be stowed within your trunk or rear cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
ModuLite Powered Tail Light Converter
A ModuLite power module is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
118405 Tow Ready T-1 T-Connector - 4 Wire - Modu-Lite
Installation Details
This Product Fits The Following Vehicles
- 2014 - 2018 Mazda 3 Hatchback
- 2014 - 2018 Mazda 3 Sedan
- 2014 - 2018 Mazda 3 with LED Taillights
- 2014 - 2018 Mazda 3 without LED Taillights
- 2003 - 2003 Mazda 6 Sedan
- 2004 - 2008 Mazda 6 Sedan and 5 Door Hatchback
- 2012 - 2017 Toyota Camry
- 2012 - 2017 Toyota Camry
- 2007 - 2009 Toyota Camry excluding Hybrid
- 2007 - 2009 Toyota Camry non-Hybrid - excluding SE
- 2007 - 2009 Toyota Camry SE excluding Hybrid
- 2014 - 2018 Toyota Corolla
- 2014 - 2018 Toyota Corolla
- 2019 - 2019 Toyota Corolla Sedan
- 2019 - 2019 Toyota Corolla Sedan
- 2007 - 2012 Mazda CX-7
- 2007 - 2012 Mazda CX-7 without factory tow package
- 2007 - 2014 Toyota FJ Cruiser
- 2007 - 2014 Toyota FJ Cruiser
California residents: click here
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Alternate product found
Customer Reviews
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118405
Average Customer Rating: 4.7 out of 5 stars (243 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.by: James 11/25/2022
Wiring harness install was easy. This is my fourth or fifth vehicle I've done this type of install. Viewed YouTube Etrailer for install video.
by: Christopher11/27/2020
2017 Mazda 3
I have a 2017 Mazda 3. I ordered the product because I was hesitant about splicing into my car’s wires. This wiring harness made things a lot easier. I watched a YouTube video to get a quick idea of how to do it. The only thing I did different was I ran the wire which connects to the battery through the inside of my car. The wire runs from the trunk, easily squeezed between the rear seat, tucked into the floor panels by the doors, goes up near the driver side, through a small pre-existing gap in the body and to the battery. No drilling though the firewall, no need to go beneath the car. See photos for reference.
Christopher
11/28/2021
Still works great. Got exactly what I paid for. Extremely satisfied!
by: Ronald03/23/2023
Easy to install. Fit and works great
Ronald
5/9/2024
Easy to install works great
by: Purvis04/10/2024
Received package 2 days early. The how to video on u-tube was very helpful. I am very pleased with etrailer. Thanks alot.
by: Rob08/18/2016
Mazda Protege5
My second hitch purchased from etrailer for a Mazda hatchback (first '02 Protege5, now '15 Mazda3). Both good experiences.
Very easy hitch install, the inclusion of the fish wires for the frame hanger bolts is a stroke of genius. Don't be afraid of the exhaust isolators, just spray some soapy water and support muffler with a jack or strap. If you can change a flat tire then you can work a wrench well enough to do this in an hour.
'14-15 Mazda3 has a couple of things making wiring easy to integrate. There's a grommet in the left rear quarter floor that's perfectly placed. Just trim some electrical tape to allow an opening, clip the new connector near the lighting adapter & reconnect inside after fishing from outside. I ran power neatly along driver's side rocker & out through the firewall. It's both easier and less vulnerable, just fish one more wire through the mass that exits above the driver's left foot. (Just DO NOT use anything sharp, you don't want to nick any wires and short something out). Finally the battery on my car already had several open connections to use right at the positive terminal, each protected by a fusible link no less! (See photo.) All I needed to add was an M6 stainless nut to connect the new wire.
Only a couple of minor downsides:
Aesthetically this is one of the uglier installs, mostly because the 3's huge muffler is right against the rear valence, leaving no room to tuck anything out of sight. My Protege5's hitch was entirely hidden except for the receiver. Here, unless you're willing to butcher your bumper cover (assuming there's a hitch made to fit that way) you're stuck with what you see in my picture. I saw the round-tube alternative on another similar car and it looked a little better, but that one requires support straps for a rack with any carrying capacity.
Design-wise I ran into one surprisingly annoying thing the first time I went to insert my drawbar. The hole in the receiver for the hitch pin is set really close to the hitch frame, and there's a gusset plate on top, which leaves basically no room for the clip that secures the pin. My existing clip didn't fit at all until I ground the ends a little. The clip that came with the new hitch sort of fit, but only jammed up against the hitch so hard that it scratched right through the protective powder coat. Weird in a product from such an experienced manufacturer, but easy to rectify.
by: Dave H.06/01/2024
This was a good recommendation from the etrailer expert. Installation was straightforward (although a little more involved than I remember from last time. He told me it is more reliable than my Curt product that had failed.
etrailer is a company I always look forward to dealing with.
by: Tim09/03/2019
2017 Toyota Camry
All equipment was delivered on time. Hitch, wiring harness, receiver and ball. Watched video's on installation of harness and hitch. Went down to my garage and installed both with the help of my girlfriend. Very satisfied with the products and the installation. etrailer supplied the goods and the knowledge. I am very happy that I went this route.
by: Heidi04/15/2020
Hitch installed easily on my 2014 Toyota Corolla.
Wiring had poor instructions in the box but the video posted on etrailer’s site answered my questions.
No issues and everything worked.
Thanks.
by: Keith 05/23/2024
2009 Toyota Camry
Great part, great service
by: Donald02/21/2024
2019 Toyota Corolla
Harness arrived rapidly, faster than Amazon. Looks to be a simmple installaion.
by: William 09/11/2023
2014 Mazda 3
Good product. Printed Instructions a little confusing but online directions were excellent.
by: Sean 03/26/2024
Easy install. Fits perfect.
by: Keith 08/29/2019
2014 Toyota Camry
Great product. This is my fourth one from etrailer. A bit more difficult to install. Had to think up some way to hold it up singlehandedly, but managed it. See attached picture.
Will deal again with you in a flash.
by: Bryon 02/10/2024
Well it worked
by: John06/07/2023
No instructions for my vehicle
Jenny N.
6/9/2023
I am sorry that the instructions were missing. I will send you a copy via email and it can also be downloaded from the product page. It is in link towards the bottom of the page before you see the reviews. We also have a video install on a 2016 Toyota Corolla.
by: Fred10/20/2022
The harness works great once installed. Printed installation instructions were general for many vehicles and woefully inadequate . On my Mazda 3 wagon I ended up drilling a hole through an internal body panel and lining it with a rubber grommet for the wire to pass through rather than running the wire between the tail light assembly and its receptacle(?) in the body panel as instructions indicated. The foam lining around the edge of the receptacle was thinner than the wire and I'm sure the wire would have been crushed between the tail light assembly and the edge of the body panel opening, and eventually short out.
by: David 10/02/2023
2014 Toyota Corolla
Package came on time and it was exactly what I ordered. Very pleased.
by: James 01/30/2023
It took four times to order because your system had my old address and finally after I talked to someone who knew what to do and he placed the order!! Although I had to pay for half of shipping!! I would like my shipping amount reimbursed!!!!
by: Tom 09/09/2022
Great trailer hitch, works great. Had it installed by a local gas station, really like the simple attachment process for both hitch and lights hookup. I highly recommend this product.
by: Len S05/04/2015
2014 Toyota FJ Cruiser
Installation is a little tedious due to tight spaces to get to existing lights. I do not understand the purpose of requiring a power source. I have stalled other wire harnesses in the past that just connect to the existing lights and on your way.
Patrick B.
7/30/2015
The purpose of the power feed is to isolate the power draw to a dedicated line. This way, if there is a short on the trailer the subsequent overload happens on the dedicated power wire, blowing the fuse, and preventing over-draw on the vehicle wiring. If the trailer lights got their power through the vehicle tail lights power, then a short on the trailer would over load those circuits potentially damaging the vehicle wiring or lights.
by: Katelyn04/03/2020
2011 Toyota FJ Cruiser
So I’m a woman and I could install this, so it’s that easy to follow. Needless to say my husband was a bit impressed. I won’t lie the wire connectors were a bit hard to clamp and connect but otherwise everything was super easy to install and works great!
Katelyn
4/5/2021
Still works fantastically, I haven’t used my trailer much during the winter, however during the fall it was still holding up quite well. I still highly recommend this product!
by: Chuck11/13/2016
2004 Mazda 6
Good product. Good price.. a little ghetto how the light wire for the trailer needs to hang out of the truck when using the trailer but that is normal for the car. After a year it works well the wire sit fine in the truck seal and never gets a cut in the wire which I was afraud of.. great set up and I would recommend it to anyone for the price.. I use the wiring and hitch on a Mazda 6 with a large 10 foot trailer and it works great.. oddly the car even handles the trailer well. Very happy
by: Kern11/13/2017
Mazda
This wiring kit was purchased for installation on a 2017 Mazda 3 sedan.
As received, the installation instructions made no reference to any Mazda 3. There was reference to a Mazda 6 with incomplete instructions and pictures. The company web site offered no further clarification.
I am an automotive engineer with an electrical background and the installation was far from obvious. Wire color codes did not match the car harness. The power wire to be routed to the battery was black. Vehicle power is usually red. The fuse holder and its wiring to be atttached to battery plus was yellow. The power wire leading into the control module was red. So, we have a yellow wire connected to a black wire, connected to a red wire. What a mish-mash!
I finally called the manufacturer and spoke with a customer service representative. He was not able to help immediately but took time to find the right information and called back.
Once the install information was received, the installation went reasonably well with the most difficult part being the routing of the power wire forward to the battery. To protect the wire and install it securely, I removed the plastic undertrays and routed the wire alongside some fuel or hydraulic lines. As mentioned by other users, more ty-wraps would have been useful. I used some from my existing supply.
After install, I tested the function with the boat trailer and it appears to work as designed.
by: Essais05/18/2018
2014 Volkswagen Passat
My third hitch from etrailer: 2000 VW Passat, 2006 Mazda 3 Sedan, now 2014 Mazda 3s GT. In all three, the plans and fit-up were excellent. For the 2014 Mazda 3s GT, I bought the 24914 Draw-tite hitch, with 3493 draw bar and 19256 ball. With the standard chrome exhaust tips, I had to lower the muffler for the hitch mounts to clear the exhaust. This was the most difficult part -- windex for lubrication and a strong grip pulled off the four rubber muffler hangars, lowering the muffler on a floor jack about 6". The hitch then fit perfectly to the mounting holes, and the part metric, part SAE hardware provided was high grade and correct. Fishing the mounting bolts through the frame members was the simplest part. Tightened nuts, raised the muffler, and then lubed and pushed on the hangars again. Done in about two hours. Four ibuprofen in anticipation of sore muscles. Nothing new. Top of the draw bar at the hitch is at 11" from the ground, putting the drawbar top at 13-1/4".
I installed the 118405 wiring harness without problems, choosing to route the power wire for the switch "converter" along under the interior trim under the doors and into the interior fuse box compartment, then into the engine compartment by a single hole punctured through an existing rubber nipple just above the wiring feedthrough on the firewall. I changed the ring connector to a 1/4" ring connector to match the existing 6 mm post on the Mazda battery terminal block (thank Mazda for the ready-made posts for accessories). Works!
Once again, etrailer gave me all I needed in one shipment, and everything fit as planned. No problems pulling my lightweight sailboat trailer and utility trailer. Another satisfied customer!
by: Joe A04/28/2020
I was very impressed with this trailer hitch. the quality the ease of installment and wiring harness. The hitch held up just fine for the past year, I would recommend this to anybody. I use it often to pull my 12 foot boat and my utility trailer and it’s only a 1 1/4 hitch on my 2015 Toyota Corolla.
Thank you for a great product
25
243
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- Can Thule Passage Trunk Mount Bike Rack be Used to Carry 86 lb E-Bike on 2016 Toyota CorollaThe Thule Passage 3 Bike Carrier # TH911XT has a total weight capacity of 105 lbs, but that's for all 3 bikes. When we break that down it comes out to 35 lbs per bike which is standard for trunk mount bike racks. For your E-Bike you're going to need to install a trailer hitch on your 2016 Toyota Corolla and go with a hitch mount bike rack. I recommend going with the Draw-Tite Trailer Hitch # 24913 and then using the Hollywood Racks Sport Rider SE 2 Electric Bike Rack # HLY74FR. This bike...
view full answer... - Recommended Ball Mount for Draw-Tite Trailer Hitch on 2014 Toyota CamryThe recommended ball mount for the Draw-Tite # 36540 trailer hitch that fits your 2014 Toyota Camry is the Ball Mount for 1-1/4" Hitch # 36071, which must be used in the rise position only, according to the installation manual of the hitch (which I have linked for you). This ball mount comes with a pin and clip to attach it to your hitch so you will not need to purchase one separately, but you will need a hitch ball. For that you will need to use either 1-7/8" Hitch Ball # 19256 or 2"...
view full answer... - Best Way to Add 7-Way Connector on 2009 Toyota FJ Cruiser for 12V Power to TrailerThe best solution for your application is to install the Tekonsha T-One # 118405 on your 2009 Toyota FJ Cruiser for your standard trailer lights and then add the Wiring Kit # ETBC7L which comes with everything you need to convert the 4-Way to a 4-Way/7-Way and add the 12V function. Please note that as power runs along that line there will be some voltage drop which will likely keep your batteries from charging completely. To help remedy this I recommend using the Redarc In-Vehicle BCDC...
view full answer... - Recommended Trailer Hitch For A 2016 Mazda 3 SedanI can definitely help set you up. You are correct in that the fitment is different for the sedan and hatchback models. For your 2016 Mazda 3 sedan I recommend the Draw Tite Class 1 # 24912. I prefer this hitch over the others we offer mainly because it will be the easiest to install. The other hitches require trimming of the bumper fascia, while the # 24912 will not. This is a standard class 1 hitch rated for towing up to 2,000 lbs. So as long as your trailer and motorcycle weigh 2,000...
view full answer... - Trailer Hitch Availability for a 2007 Toyota Camry SEWe do have the Draw-Tite Trailer Hitch # 36416 that is compatible with your 2007 Toyota Camry SE. This is a Class II trailer hitch with a 1-1/4" receiver and it has a 3,500 lb gross trailer weight rating as well as a 300 lb tongue weight rating. When I looked up an online copy of your owner's manual it stated on page 327 that the max amount of trailer weight it can tow is 1,000 lbs and then it also stated that the max tongue weight of your Camry is 100 lbs. Even though the trailer hitch...
view full answer... - What Size Bolts Hold Tow Hooks on 2009 Toyota FJ Cruiser in PlaceThe bolts holding the tow hooks in place are M12x1.25. I've linked to the install instructions for the Curt # 13367 hitch you'd looked at. If you'll be towing with the hitch, you'll also need a trailer wiring harness like part # 118405, a ball mount like part # 2753 and # 19260 for a 1-7/8 or # 63845 for a 2 inch trailer ball. I've linked to installation videos for the hitch and the trailer wiring harness.
view full answer... - Amperage of Fuse for 118405 T-One Wiring Harness The fuse that comes with the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118405 uses a 10 amp fuse. It's probably a good idea to bring the fuse holder along with you to make sure you can find a match when getting a spare. I have added links to a couple install videos as well as the instructions of Trailer Connector # 118405 for you to check out. I also highly recommend using Dielectric Grease for Electrical Connectors # 11755 to help prevent any type of corrosion...
view full answer... - Trailer Wiring for 2016 Mazda 3 that Fits Sedan/Hatchback with or Without LED LightsI have an easier solution for you, but at this time Curt does not list any of their trailer wiring kits for the 2013 Mazda 3 as a fit if the vehicle has LED taillights. Instead we have the Tekonsha kit part # 118405 which fits all versions of the 2016 model including with or without LED lights and hatchback or sedan. Plus the Tekonsha kits have a reputation as having the most reliable converter boxes so we recommend them highly. I attached an install video for more info for you to check...
view full answer... - Installing 7-Way Trailer Wiring Harness On 2015 Toyota Corolla To Match Trailer ConnectorYou said you have a flat pin 7-way connector on your trailer. If the trailer has a round connector that has flat pins it is probably because the trailer has brakes. For your 2015 Corolla you would first need a 4-way connector and then a 7-way. The 4-way wiring harness I recommend is the T-One # 118405. This connector attaches to the vehicle wiring behind the driver and passenger side tail lights in the rear cargo area. You will need to remove some carpeting or interior trim to access...
view full answer... - 2014 Camry XLE Hybrid Towing CapacityI looked up the towing capacity of your 2014 Camry XLE Hybrid online and found it to be 1,115 lbs which would be enough for a small rental trailer. We have just what you'd need to tow a small trailer too. First you need a hitch which for that we have the Curt part # C12107 as a fit that would have plenty of capacity. For trailer wiring you'd then want the part # 118405 which has the most reliable converter box available and is easy to install. Then for a ball mount you'd want the Curt...
view full answer... - Can a 2014 Toyota Camry SE Tow Small Trailer from Arkansas to San Diego? According to your owner's manual the 2014 Toyota Camry is not recommended to tow. People have of course used it for light towing and there is a hitch # 36540 which will give you that ability you will just be functioning outside of your warranty. If you choose to tow, you are not looking at a lot of weight. Some websites will show a 1,000 lb towing capacity for your vehicle. Then you will need a ball mount # 36071, a hitch ball # 19258 and a wiring harness # 118405.
view full answer... - Trailer Hitch and Wiring Recommendation for Towing and Bikes for a 2004 Mazda 6 HatchbackIf I were choosing a trailer hitch for a 2004 Mazda 6 hatchback the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11308 is the right choice. You mentioned you might do some towing. The appropriate ball mount and pin and clip is # 3592. All that would be needed is a ball # 19256 for a 1-7/8 inch or # 19258 for a 2 inch. The Curt hitch # C11308, requires the use of stabilization strap # 18050 when using the hitch with a bike rack or cargo carrier for Curt's warranty requirements,...
view full answer... - Trailer Hitch Recommendation for 2012 Toyota CamryClass III 2 inch trailer hitches are only available for heavier duty vehicles like trucks and SUVs which have higher towing capacities. For your 2012 Toyota Camry we only have Class II hitches like the Draw Tite part # 36540 which has a 1-1/4 inch hitch opening. You'd either have to look into a small trailer to tow with your Camry or look into a larger vehicle. For trailer wiring for the Camry you'd want the Tekonsha # 118405. For a ball mount # 3593 and hitch balls # 19256 for a 1-7/8...
view full answer... - Will The T-One Vehicle Wiring Harness Item # 118405 Fit A 2015 Toyota Corolla S ModelGreat question! Yes, the T-One Vehicle Wiring Harness Item # 118405 is compatible with your 2015 Toyota Corolla S. I have included a link to an instillation video on a 2016 S. The instillation will be the same. This wiring harness lives in the trunk of the vehicle however, in the video I talk about how you would run the 4 pole end out with the power wire so it can be mounted outside the vehicle. If you choose to route the 4 pole outside the vehicle, I recommend adding a No-Drill Mount...
view full answer... - Parts Needed to Install a 7-way on a 2014 Toyota FJ CruiserSo it sounds like you are possibly trying to wire in a second 7-way to your 2014 Toyota FJ Cruiser. Which if that is the case the part # 41157 would be what you would need. Or if you are just trying to install a 7-way in general on a vehicle that does not have one you would first need to start with a 4-way. For that you would want the part # 118405 which is a confirmed fit that plugs in line with the taillight hosing of your vehicle. Now if your trailer does not have brakes all you would...
view full answer... - Prodigy Trailer Brake Controller Installation in 2008 Toyota FJ CruiserTrailer brake controllers such as the Prodigy P2 # 90885 and P3 # 90195 are not vehicle-specific so you can install any controller you like in your 2008 Toyota FJ Cruiser. The P2 and the P3 are very similar in actual technology and operation but the P3 adds some nice features that make it easier to use, such as storable trailer braking power settings and a larger display. Any controller you choose will install in your FJ using our installation kit # ETBC7. This includes all of the parts...
view full answer... - 2012 FJ Cruiser 4-Way Trailer Wiring RecommendationFor 4-way trailer wiring for your 2012 Toyota FJ Cruiser you would want the part # 118405 that has been confirmed as a fit for your vehicle. The wiring harness you found could be for trailer wiring but it is not a style of connection that we sell a harness for. There might be a Toyota option that you could get through a dealer. The part # 118405 installs inline with the taillight assemblies of your vehicle to provide the 4-way signal. I attached an install video for you to check out.
view full answer...
- How To Tell If Lights On 2015 Mazda 3 Are LED Or IncandescentYou can find out if you have LEDs a couple of ways. The easiest is to remove the lens of the lights and if it has a bulb it is incandescent. If it has diodes then it is LED. Another way is to turn the lights on and then watch as you turn them off. If the light go off abruptly, they are probably LED. If the filament takes a moment to go out then it is probably a bulb. The third way is to contact your dealer with the VIN and they will be able to tell you what lights are on your Mazda 3.
view full answer... - Trailer Hitch and Wiring for a 2015 Toyota Camry SEWe do have a Curt hitch to fit your 2015 Toyota Camry but trailer hitch # C11298 is for a 2000 to 2005 Saturn L Series sedan or wagon. The Curt equivalent hitch for your 2015 Camry is # C12107. You also need the proper ball mount # C45017 for towing. For compatible balls use # A-80 for a 1-7/8 inch diameter ball or # A-82 for a 2 inch diameter ball and the pin and clip # F-4. And for trailer wiring you can use # 118405 to add a 4-Way flat connector to the rear of the vehicle. If you...
view full answer... - Hitch, Weight Distribution System, Sway Control, Brake Controller, Wiring for 2007 Toyota FJ CruiserWeight Distribution is a good idea if you are pulling at least 50 percent of your vehicles weight. Many good WD systems come with sway control, too, so we will look at those. First, you will need a hitch. I recommend the Curt Trailer Hitch, # 13367, which is a custom fit item for your 2007 Toyota FJ Cruiser, unless your FJ is equipped with the auxiliary fuel tank. The hitch will bolt to the frame and this one will install in about 30 minutes. I have included a link to the instructions...
view full answer... - Is There A Hitch Available For A 2017 Toyota Camry That Can Handle 500 Pounds Of Tongue Weight?The trailer hitches offered for your 2017 Toyota Camry will all be Class 2 rated hitches. There can be a little variance with max capacity in this class and the highest rated one is the # C12107, offered by Curt. This is a custom fit hitch and will have a pretty easy install (see attached video), but this will have a max tongue weight of 350 pounds (which is the highest Class 2 hitches go up to). Unfortunately, there is not a way to get a hitch with more tongue weight than this, and, to...
view full answer... - Will A Hitch Void the Warranty Of My 2018 Mazda 3 Grand Touring and Which Hitch is Recommended The act of installing a hitch on the 2018 Mazda 3 Grand Touring will not void the warranty because you are covered under the Magnuson–Moss warranty act which prohibits manufacturers from voiding a warranty for adding aftermarket parts unless that after market part caused damage the vehicle. With that said, if Mazda does not recommend towing anything with the Mazda 3 Grand Touring (more than likely they mention it in the owners manual) if towing damages the transmission or any other mechanical...
view full answer... - Trailer Hitch Recommendation for a 2014 Toyota CamryYes, the Draw Tite hitch part # 36540 that you referenced has been confirmed to fit all models of the 2014 Toyota Camry so it would work well on your non-Hybrid. For a ball use # 19256 for a 1-7/8 inch diameter or # 19258 for a 2 inch diameter. For trailer wiring, use # 118405. I have included a link to the trailer wiring for you.
view full answer... - No Power on Curt Trailer Wiring Harness on a 2007 to 2012 Mazda CX-7Trailer wiring harnesses # C55593 for the Mazda CX-7 will only fit if the vehicle came with the factory tow package. It sounds like your model did not. What you will need to add trailer wiring is a different type of harness, # 118405. It is possible that even if you ran a power wire to the battery manually and bypassed that connector it might still not work. going with harness # 118405 would be the sure thing.
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Alan C
Test Fit:
Randy B
Test Fit:
Shane H
Test Fit:
Ryan G
Expert Research:
Mike L
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Dustin K
Video Edited:
Sue W
Video Edited:
Chris R
Video by:
Andrew K
Video by:
Kathleen M
Video by:
Jonathan Y
Updated by:
Adele M
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
Installed by:
Cole B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
James
11/26/2023
Ive had this installed for a year with no issues. Works perfectly!