Difference Between Hitches for 2006 Toyota Highlander
Question:
Is there any real difference between the three hitches for a 2006 Toyota Highlander?
asked by: Jay
Expert Reply:
The only difference between the Curt Class III Hitch # 13530 and the Draw-Tite # 75153 is that the Curt hitch has the safety chain loops welded to the bottom of the receiver, while the Draw-Tite model has the safety chain loops welded to the top.
Both models are very similar in appearance and would install in the same manner. The only difference is that the Curt # 13530 can be used with weight distribution, where it carries a 4000 lb GTW and 400 lb TW rating.
I have linked to the install instructions as well as some install videos that you might find helpful.
In addition to the hitch, you might also need the following to complete your towing system:
Wiring harness with 4-pole trailer connector, # 118413
Ball mount, # C45010
2 inch trailer ball, # 19247
1-7/8 inch trailer ball, # 19260
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Can Spare Tire Be Accessed After Mounting Curt Class III Trailer Hitch # 13530 on 2009 Lexus RX350
- Q&A: Brake Controller in a Volvo 780 VNL Semi for Towing Trailer with Electric Brakes
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between the Kuat NV 2.0 and the Older Version of the Rack
- Q&A: Is there a 12 Inch Trailer Tire that is Rated for 80 Miles Per Hour
- Q&A: Trailer Hitch that Fits 2022 Kona N
- Q&A: Replacement Titan Master Cylinder that is Stamped 23744
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Hitch Receiver Sizes
- Article: Routing the Power Wire for a Trailer Wiring Harness