Replacement Stabilizer Jack for a 2011 Fun Finder X 189 FBS

Question

Question:

Do you sell a replacement stabilizer jack for the front end of a 2011 Fun Finder X 189 FBS?

asked by: Larry O

0

Expert Reply:

Your 2011 Fun Finder trailer could have been fitted with any number of brands of stabilizer jacks. I have included a link to the options we carry.

Jack # UF48-979006 is a popular option.

expert reply by: Michael H

0

Answer 1

For your electric jack, there are only three possible explanations for your jack not working with a charged battery. Either power is not getting to your motor, your motor is bad, or your ground connection isn't working properly. To test power,…

view full answer...

Answer 2

There are 4 screws on the bottom of the bottom cover holding it to the top. And if you remove the cap on the very top of jack #LC285318 you will see 2 more screws. With all the screws removed you should have no problem with the cover. These very…

view full answer...

Answer 3

There are four screws that hold the lid part #LC285160 to the rest of the Lippert jack part #LC285318. If you check out the picture I attached you'll see the screw holes pointed out.

view full answer...

Answer 4

When it comes to checking your retract/extend functions not working it sounds like you may just need to swap some wiring on the back. I will attach picture of the wire swaps. It sounds funny but per the manfuacturer that does seem to help. If that…

view full answer...

Answer 5

Each of the leaves on the Leaf Spring #e47SR are 3/8" so this will give the spring pack a height of 1-1/2". Here is a list of our U-Bolt Kits for a 3" axle. Redline #APUBR-9 Dexter #APUBR-8 CE Smith #CE23003

view full answer...

Answer 6

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 7

The etrailer Scissor Jacks part #TJSCHD-24-4 would work great on your Keystone Premier Travel Trailer. It has more than enough capacity as it's rated for up to 10k and has a universal mount design that will fit your trailer.

view full answer...

Answer 8

I've attached a dimensional drawing for the Ark XO Drop Down Corner RV Stabilizer Jacks #ARK87FR, which displays the measurements in mm and inches. If you need anything else please let me know and I'd be happy to help.

view full answer...

Answer 9

The stabilizing jacks are all made overseas, and in regards to the capacities, they are on a per-jack basis. So the Scissor Stabilizer Jacks with Handle - 18-3/4" Lift - 10,000 lbs - Qty 4 #TJSCHD-24-4 have a 2,500 lb capacity per jack. The…

view full answer...

Answer 10

I do have options for you but none of our swing down stabilizer jacks have an extended length longer than 18". Instead, I recommend using the Ultra-Fab Ultra Scissor Jacks part #UF48-979002 which have a 6,500 lb weight capacity and 24"…

view full answer...

Answer 11

The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn. If the spindle uses a castle nut and cotter pin or tang nut, tighten the nut finger tight until it…

view full answer...

Answer 12

There is no difference between the 2,500 version of the SnapPad SnapJack for RV Scissor Jack Stabilizers, and the 5K to 7K version #SN65FR. The only difference between the two would be the capacity they can handle. In order to determine which one…

view full answer...

Replacement Stabilizer Jack for a 2011 Fun Finder X 189 FBS

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching