Replacement 7-Way Connector for 2007 Chevrolet Silverado

Question

Question:

does the plug slide into socket into a 2007 chevy silerado or twist I need it to slide in

asked by: John

0

Expert Reply:

The Hopkins Endurance Multi-Tow Trailer Connector, # HM40920, is a twist-in socket.

If you need a slide in replacement 7-way/4-way connector for your 2007 Chevrolet Silverado, you can use the Hopkins Custom Fit Vehicle Wiring, # 30955.

I have attached a video for you to check out.

expert reply by: Leah S

0

Answer 1

Yes, the Hopkins 7-way part #HM40920 is a twist mount like what your 2012 Chevy Silverado requires. I attached an install video for this on a similar Silverado as yours for you to check out as well.

view full answer...

Answer 2

It is possible to use both the 7 way and the 4 way plug on the Hopkins Endurance Trailer Connector #HM40920 at the same time. Since both plugs use the same wiring, they will both be active at all times. That being said, using both at the same time…

view full answer...

Answer 3

The Hopkins Endurance Multi-Tow Twist Mount #HM40920 will fit variety different vehicle's that have the twist mount on the rear of the truck. If your popup camper has either a 4-way or 7-way trailer plug connector, then it will be compatible with…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you don't mind drilling Jeremy I would recommend using all three mounting holes of the Dexter Actuator part #DX89FR or if you know a welder just have them weld it to the trailer. If you were going to only use two though use whichever two line…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

To install the B&W Patriot 5th Wheel Trailer Hitch #BWRVK3200 in your 2003 Chevy Silverado 3500 the best option is the B&W Custom Installation Kit w/ Base Rails #BWRVK2500 because it will not require drilling into your truck's frame rails…

view full answer...

Answer 11

To determine the maximum trailer weight capacity you can tow with your 2006 Chevy Silverado 2500, you will need take your Gross Combined Weight Rating (GCWR) and subtract that by the the Gross Vehicle Weight (GVW) of your truck from the (GCWR) that…

view full answer...

Answer 12

To install the B and W Fifth Wheel Rail Kit part #BWRVK2500 in your 2006 Chevy Silverado requires no drilling into the frame. Holes would need to get drilled through the truck bed but that's it.

view full answer...