Parts Recommendation for a 2005 Chevy Malibu Maxx to tow a 2,000 lb Boat and Trailer
Question:
May I tow with a malibu Maxx 2005 and the Curtis hitch C 12280 a trailer with 17foot boat with a total of 2,000 lb ? It will be used for very short distance.
asked by: Gino
Expert Reply:
First thing you need to do is check the owner's manual of your 2005 Chevy Malibu Maxx under the towing section to see what Chevy lists as the towing capacities of your vehicle.
The Curt Hitch part # C12280 that you referenced is confirmed to fit your vehicle and has towing capacities of 350 lbs tongue weight and 3,500 lbs total trailer weight. If your owner's manual lists a lower figure you will need to go with that as the capacity as a towing setup is only as strong as it's weakest component.
For trailer wiring you would want the Curt Harness part # C56013. The recommended ball mount is part # C45520, pin and clip # F-4, 1-7/8 inch ball # C40001, 2 inch ball # C40018.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-5/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 3 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Installation of Curt Class II # C12280 Hitch on 2005 Chevy Malibu Maxx
- Q&A: Stromberg Carlson Bike Bunk Used With Pop-Up Camper
- Article: Trailer Hitch Installation Tips
- Q&A: Trailer Wiring Kit That Fits 2023 Kia Telluride