Changing Wire Rope on a Superwinch Terra 3500 Pound Capacity Winch

Question

Question:

How does the rope hook up to drum I have a 3500 lb super winch

asked by: Barry

0

Expert Reply:

There is a hole in the drum and a set screw that takes an allen wrench. You would put the winch in free spool mode, pull the old cable all the way out and loosen the set screw to take the cable out. Reverse the process to put the new cable on.

expert reply by: Michael H

0

Answer 1

On your Superwinch LT3000 model winch there is a small set screw that's keeping the wire cable in place on the drum. This screw needs to be removed in order to release the existing cable so that a new one can be installed in its place. When…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

The main difference between a Class III hitch and a Class IV hitch is the capacities they set for the hitches. Class III hitches are rated for up to 6,000 lbs GTW with 600 lbs TW whereas a Class IV is rated for up to 12,000 lbs GTW and 1,000 TW.…

view full answer...

Answer 6

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Answer 7

I would discourage the use of an adapter for use of 2 inch accessories in 1-1/4 inch trailer hitch receivers. The reason is that the adapter places the carrier farther away from the rear of the vehicle and hitch, creating additional torque that 1-1/4…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

Since your Brake Buddy Vantage Select, similar to the Select 3 #HM39524, needs to connect to a 12V power socket you'll need to install the 12V Outlet Kit #RM-9332 on your 2016 Ram 1500. You could potentially keep your truck turned on but it would…

view full answer...

Answer 11

4WD models of the 2022 Ram 1500 are able to be flat towed, with a few steps listed in the owner's manual. TO flat tow your Ram you'll need a baseplate, tow bar, tow bar wiring kit, braking system, and safety cables. For these components I…

view full answer...

Answer 12

For your 2022 Ram 1500 I recommend the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle #AL88375. The LoadLifter 5000 Ultimate air springs have internal bumpers, so you get the adjustable load support of…

view full answer...

Changing Wire Rope on a Superwinch Terra 3500 Pound Capacity Winch

Product Page this Question was Asked From

Continue Researching