Installation Instructions for the Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter # CAB-C5G

Question

Question:

Can I get the installation instructions for a cushioned 5th wheel adapter? I bought one but the guy didnt have the instructions. If I need to purchase them I will just let me know. Thanks

asked by: Buddy

0

Expert Reply:

I attached the two pages of the installation instructions for the Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter # CAB-C5G for you to check out.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

Since the bolt holes line up vertically and horizontally you'll be able to bolt the Trailair Air Ride 5th Wheel King Pin - Leland 7920 #UF35-946208. This specific pin box actually has an 18" king pin to first set of bolt holes measurement…

view full answer...

Answer 3

The best option I have for you to tow a 5th wheel trailer using a flat-bed truck with recessed gooseneck hitch is with the Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter part #DM8550046. The Demco Recon is designed for this exact purpose…

view full answer...

Answer 4

Hey Brad, thanks for reaching out! What pin box number do you currently have installed on your 2021 Grand Design Reflection 31MB? You should find a sticker with a number like "1621" or even a serial number and the brand would work. Not all…

view full answer...

Answer 5

Your 5th wheel is equipped with a Venture CJ13517 pin box, and I'm sorry to say that there is not a compatible Gen-Y Goose Box model. So your best bet will be to continue to use your B&W Companion hitch. If you want to replace your pin box,…

view full answer...

Answer 6

Hey William, the E6 error on a Furrion wall thermostat indicates an Open circuit Humidity Sensor issue. Most likely the sensor is bad and needs to be replaced as this is a pretty rare error code.

view full answer...

Answer 7

I took a look at the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 that you mentioned and it's actually going to be a fit for the Lippert 1621 and 1621 HD 5th-wheel pin boxes, and not your Leand 7920, however I do have another…

view full answer...

Answer 8

For your 2017 Ford F-350 dually with the factory hitch prep package the B and W Companion Slider part #BWRVK3370 is a confirmed fit and would work well. It's not going to fit with you welder and tool box though so you'd have to remove them to…

view full answer...

Answer 9

The bolts that attach the adapter to the king pin are through bolts, meaning if one broke the nut and other half of the bolt should be lying in the pin box. If you are able to make your way to a hardware store you can get a 1/2 inch grade 8 bolt, 1/2…

view full answer...

Answer 10

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 11

You might be able to find a sticker on either leg that will tell you who the manufacturer is and what the part number is for the leg as well. If you aren't able to find that then you can try reaching out to Forest River with your VIN to see if…

view full answer...

Answer 12

The compressor should have a 12 volt keyed source that tells the compressor when to turn on. Most likely someone wired your keyed source straight to the battery which allows it to be active all the time. Which compressor did you install?

view full answer...

Installation Instructions for the Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter # CAB-C5G

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching