Ball Mount with 2 Inch Rise Longer than 7 Inches to Tow Trailer Level with 2001 Subaru Forester
Question:
I have a 1 and a quarter hitch receiver which is 12 inches from ground to top of receiver. I need to get to 14 inches for level ride for tear camper. It seems that I need a longer shaft than 7 inches.
asked by: Jeff T
Expert Reply:
It sounds like there are a couple of things going on here. First, you need a ball mount with a 2 inch rise. But then it also sounds like you need a ball mount that is longer than 7 inches. The other issue is that on Class I and II hitches you are supposed to use the ball mount recommended by the hitch manufacturer or it could void the hitch warranty.
Ball mount # 3592 is going to be the best bet for the height and length requirements. It has a 2-1/8 inch rise and measures 9-3/4 inches long from the center of the hitch pin hole to the center of the ball hole. And it measures 6-1/2 inches from the center of the hitch pin hole to the nearest part of the ball platform. This ball mount is rated for 2,000 pounds gross trailer weight.
For a higher capacity of 3,500 pounds, you can use # C45016. It has a rise for 2-5/8 inches and measures 9-3/8 inches from the center of the hitch pin hole to the center of the ball hole.
You could also look at the Brophy Ball Mount # BM20 which is 13-1/4 inches from the center of the hitch pin hole to the center of the ball hole. This is rated at 10,000 pounds.
Products Referenced in This Question
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 9-3/4" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Product Page this Question was Asked From
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Brophy
more information >
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: How to Figure Weight Capacity When Using a Hitch Extender or Extra Long Ball Mount
- Q&A: Difference Between Brophy # BM20 and # BH20 Ball Mounts
- Q&A: Extended and Retracted Height of ARK ORJW1SU Extreme Off-Road Ratcheting Trailer Jack
- Q&A: Stowed Length of ARK ORJW1SU Off Road Trailer Jack
- Q&A: Will Extreme Ratcheting Trailer Jack Keep Moving Forward without Handle if in Forward Position
- Q&A: Is 770 Lbs for the Extreme Off-Road Ratcheting Trailer Jack Trailer or Tongue Weight
- Q&A: Safety of Using Hitch Extender and Other Options To Clear Spare Tire on Jeep Liberty
- Article: Hitch Adapters and Extenders
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Article: Stability Control for Heavy Duty Vehicles
- Article: Which Sway Control Hitch is Right For Your Trailer?