Options For A Tongue Jack With Low Retracted Height For An ATV Trailer
Question:
Without a photo of the jack this will be difficult to describe: can I remove the inner tube and cut off a few inches of the outer tube, then re the inner tube? My goal is to get the tongue even lower than 10 ½inch to tow trailer with ATV 4 wheeler
asked by: George
Expert Reply:
Hello George. I believe I understand what you are describing. I really cannot recommend modifying a jack in the way you described though. If you need something with a retracted height of less than 10-1/2" we do have a few options for you.
One is the Square Jack w/ Footplate # MJSQ-2500B. This jack has a 7-1/4" retracted height. As far at the bolt on tongue jacks we offer, this will have the lowest clearance of all of them. The only downside is that this jack has a footplate and not a wheel.
If you need something with a wheel, we do have the Fulton Fixed-Mount Marine Jack # TJ12220301 which has a 6" diameter wheel and a 9" retracted height.
What you can do is get the trailer level and measure from the center of the tongue to the ground. This will give us a good idea of exactly what kind of retracted height will be needed for a jack. If you want to take that measurement feel free to drop it in the comments below and I can make sure you get something that will work.
Products Referenced in This Question
etrailer Boat Trailer Jack w/ Footplate - Sidewind - Fixed Mount - 29-1/8" Lift - Zinc - 2.5K
- Trailer Jack
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 2001 - 3000 lbs
- Sidewind Jack
- 29 Inch Lift
- Bolt-On
- With Rectangle Foot
- etrailer
more information >
Fulton Fixed-Mount Marine Jack - Sidewind - 1,200 lbs
- Trailer Jack
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- 15 Inch Lift
- Bolt-On
- With Wheel
- Fulton
more information >
Product Page this Question was Asked From
etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 11" Lift - Zinc - 1.2K
- Trailer Jack
- Boat Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 11 Inch Lift
- Bolt-On
- With Wheel
- etrailer
more information >
Continue Researching
- Q&A: Will the Draw-Tite Trailer Hitch Fit a 2022 Volvo XC90 Recharge
- Q&A: Kit to Convert 2021 Vanleigh Pinecrest 335RLP to Electric Over Hydraulic Disc Brakes
- Q&A: Best Upgrade for Dometic 310 Part-Timer RV Toilet
- Q&A: How To Connect A Dometic 310 RV Toilet To A Supply Line That's Too Far Away
- Article: How to Charge a Trailer Battery While Driving: 3 Common Problems (And How to Fix Them)
- Article: 2023 Best Gifts for Outdoor Enthusiasts
- Q&A: How To Setup a 2019 Jeep Cherokee Trailhawk for Flat-Towing
- Q&A: Typical Trailer Suspension Hanger Spacing Relative to Leaf Spring Size
- Q&A: Hanger Spacing for 3500 LB. Tandem Axle Trailer
- Article: Harvest Hosts
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Article: Tire TLC: How & When to Check Your RV/Trailer Tire Pressure
- Article: 2023 Holiday Must Haves